Specification sheet Wheel Loader Ref caterpillar-910m-wheel-loader
Caterpillar 910M
The Caterpillar 910M is a wheel loader with an operating weight of 17,893 lb (8,116.13 kg), and a 97 hp engine.
✓ QA-verified — every figure checked for unit consistency, physical possibility, and class plausibility; failures withheld → Operating weight
17,893lb
8,116.13kg
Engine power
97hp
72.4kW
Net Power ◆Where it sits in its classpercentile · compact wheel loaders
Among 374 compact wheel loaders (≤22,000 lb), the Caterpillar 910M sits above the median for its class:
- Operating weight 17,890 lb heavier than 78% (n=374)
- Engine power 97 hp more powerful than 77% (n=367)
Not positioned on bucket capacity — withheld or unpublished for this machine.
01 Engine Specification
| Net Power | 97hp | 72.4kw |
|---|---|---|
| Displacement | 268cu in | 4.4L |
| Bore | 4.2in | 105mm |
| Stroke | 5in | 127mm |
| Emissions | Engine meets U.S. EPA Tier 4 Final/EU Stage IV emission standards. | |
| Engine Model | Cat C4.4 ACERT | |
| Rated Net Power - Iso 9249 | 97hp | 72.4kw |
| Note | Net power advertised is the power available at the flywheel plus front drive implement pump when the engine is equipped with fan, air cleaner, muffler and alternator. | |
| Maximum Gross Power - Sae J1995 | 102hp | 76.1kw |
| Maximum Gross Power - Iso 14396 | 100hp | 74.6kw |
| Maximum Gross Power | 100hp | 74.6kw |
| Maximum Gross Power - Iso 14396 (Din) | 101hp | 75.4kw |
| Maximum Gross Torque - Iso 14396 | 332lb ft | 450.2Nm |
| Maximum Net Torque - Sae J1349 | 325lb ft | 440.7Nm |
| Rated Net Power - Sae J1349 | 96hp | 71.6kw |
| Rated Net Power - Iso 9249 (Din) | 98hp | 73.1kw |
| Maximum Gross Torque - Sae J1995 | 336lb ft | 455.6Nm |
| Maximum Net Torque - Iso 9249 | 329lb ft | 446.1Nm |
| Maximum Gross Power - Maximum Engine Speed | 2350rpm | |
| Rated Net Power - Rated Engine Speed | 2200rpm |
02 Operational Specification
| Operating Weight | 17893lb | 8116.2kg |
|---|
03 Transmission Specification
| Note | *Creeper Control allows speed control from a stand still up to 10 km/h (6.3 mph). The Creeper Control will only work in Range 1. |
|---|
04 Steering Specification
| Maximum Working Pressure - Steering Pump | 2683 psi | |
|---|---|---|
| Steering Articulation Angle - Each Direction | 40 degrees | |
| Number Of Steering Wheel Turns - Full Left To Full Right Or Full Right To Full Left | 3.75 turns | |
| Maximum Flow - Steering Pump | 17 gal/min | |
| Steering Cycle Times - Full Left To Full Right - At 2,350 Rpm: 90 Rpm Steering Wheel Speed | 3.2 s |
05 Transmission Specification
| Forward And Reverse - Low Range, Speed Range 1* | 6.3mph | 10.2km/h |
|---|---|---|
| Forward And Reverse - Low Range, Speed Range 2* | 12.5mph | 20.2km/h |
| Forward And Reverse - High Range | 25mph | 40.3km/h |
06 Tires Specification
| Note (1) | Other tire choices are available. Contact your Cat dealer for details. | |
|---|---|---|
| Note (2) | In certain applications, the loader's productive capabilities may exceed the tire's tonnes-km/h (ton-mph) capabilities. | |
| Note (3) | Caterpillar recommends that you consult a tire supplier to evaluate all conditions before selecting a tire model. | |
| Standard Size | 15.5-25 12PR | |
| Other Choices Include | 15.5-R25; 17.5-25 12PR; 17.5-25 12PR L2; 17.5-R25 XHA * L3; 17.5-R25 * L2/L3 PC RM; 17.5-25 16PR L3, 3PC Rim; 17.5-25 GY L2/L3; 17.5-25 12PR L2, SNOW; Flexport |
07 Buckets Specification
| Bucket Capacities | 1.3 m3-1.9 m3 (1.7 yd3-2.5 yd3) |
|---|
08 Axles Specification
| Front | Fixed; Locking differential (standard) | |
|---|---|---|
| Rear | Oscillating 11 degrees; Locking differential (Standard) |
09 Operating Specifications Specification
| Rated Bucket Capacity | 2.5yd3 | 2m3 |
|---|
10 Service Refill Capacities Specification
| Cooling System | 5.7gal | 21.6L |
|---|---|---|
| Fuel Tank | 40.7gal | 154.1L |
| Hydraulic Tank | 14.5gal | 54.9L |
| Hydraulic System - Including Tank | 25.9gal | 98.1L |
| Engine Crankcase | 2.3gal | 8.8L |
| Transmission | 0.9gal | 3.5L |
| Note | DEF used in Cat SCR systems must meet the requirements outlined in the International Organization for Standardization (ISO) standard 22241-1. | |
| Axles - Front Center Differential | 2gal | 7.6L |
| Axles - Rear Center Differential | 2gal | 7.6L |
| Diesel Exhaust Fluid (Def) Tank | 5gal | 19L |
11 Cab Specification
| Rops | ISO 3471:2008 | |
|---|---|---|
| Fops | ISO 3449:2005 Level II | |
| Note (1) | Cab and Rollover Protective Structures (ROPS) are standard in North America and Europe. | |
| Note (2) | The declared dynamic operator sound pressure levels per ISO 6396:2008*, when properly installed and maintained, is 77 dB(A). | |
| Note (3) | The labelled sound power level for the CE marked configurations when measured according to the test procedure and conditions specified in 2000/14/EC is 103 dB(A). | |
| Note (4) | *The measurements were conducted with the cab doors and windows closed. |
12 Loader Hydraulic System Specification
| Maximum Flow - Implement Pump | 32 gal/min | |
|---|---|---|
| Maximum Working Pressure - Implement Pump | 3408 psi | |
| Maximum Flow - Implement Pump - 4th Function, Maximum Flow | 24 gal/min | |
| Relief Pressure - Tilt Cylinder | 4931 psi | |
| Relief Pressure - Tilt Cylinder - 3rd Function Maximum Working Pressure | 3046 psi | |
| Relief Pressure - Tilt Cylinder - 4th Function Maximum Working Pressure | 3046 psi | |
| Hydraulic Cycle Time - Raise, Ground Level To Maximum Lift | 5.2 s | |
| Hydraulic Cycle Time - Dump, At Maximum Reach | 1.4 s | |
| Hydraulic Cycle Time - Rackback | 2.2 s | |
| Hydraulic Cycle Time - Float Down, Maximum Lift To Ground Level | 3.7 s | |
| Hydraulic Cycle Time - Total Cycle Time | 12.5 s | |
| Maximum Flow - Implement Pump - 3rd Function, Maximum Flow | 24 gal/min |
?Questions & answersfrom this machine's data
- How much does a Caterpillar 910M wheel loader weigh?
- A Caterpillar 910M wheel loader has an operating weight of 17,893 lb (8,116.1 kg).
- What engine does a Caterpillar 910M wheel loader have?
- A Caterpillar 910M wheel loader is powered by a Cat C4.4 ACERT engine producing 97 hp (72.4 kW).
Method. Figures are manufacturer reference specifications, not measurements. Every value is checked for unit consistency, physically possible magnitude, and plausibility for its equipment class before publication; figures that fail any check are withheld rather than shown, and figures reconstructed from related data are marked above. Imperial and metric figures are reproduced as published, except where a note states otherwise.