Specification sheet Skid Steer Loader Ref caterpillar-252-skid-steer-loader

Caterpillar 252

The Caterpillar 252 is a skid steer loader with an operating weight of 7,615 lb (3,454.2 kg), a 59 hp engine, a rated operating capacity of 2,250 lb (1,020.59 kg), and a tipping load of 4,500 lb (2,041.17 kg).

✓ QA-verified — every figure checked for unit consistency, physical possibility, and class plausibility; failures withheld →
Operating weight
7,615lb
3,454.2kg
Engine power
59hp
44kW
Net Power
Rated operating capacity
2,250lb
1,020.59kg
Tipping load
4,500lb
2,041.17kg
Bucket capacity
0.6yd³
0.5m³

Where it sits in its classpercentile · skid steer loaders

Among 360 skid steer loaders , the Caterpillar 252 sits above the median for its class:

  • Operating weight 7,620 lb heavier than 71% (n=334)
  • Engine power 59 hp less powerful than 57% (n=335)
  • Rated operating capacity 2,250 lb higher-rated than 69% (n=288)

Scale drawingdrawn to scale · mm

2080C229D3616A2910B
Side elevation
2080C1829E
Front elevation

01 Engine Specification

Number Of Cylinders 4
Engine Make 2236
Engine Model 3034
Gross Power 63hp 47kw
Net Power 59hp 44kw
Power Measured @ 2600rpm
Displacement 183cu in 3L
Bore 3.9in 97.1mm
Stroke 4in 100.1mm
Engine Model Cat 3034C
Net Flywheel Power 59hp 44kw

02 Operational Specification

Operational Weight 3535lb 1603.5kg
Fuel Capacity 23.8gal 90L
Max Speed 7.6mph 12.1km/h
Hydraulic System Fluid Capacity 14.1gal 53L
Operating Speed 7.6mph 12.1km/h

03 Loader Specification

Operating Load Rating 2250lb 1020.6kg
Bucket Capacity 0.6yd3 0.5m3

04 Weights Specification

Operating Weight 7615lb 3454.2kg

05 Hydraulic Specification

Pump Flow Capacity 22gal/min 83L/min

06 Hydraulic System Specification

Loader Hydraulic Pressure 3300 psi
Loader Hydraulic Flow 22 gal/min
Hydraulic Flow Standard flow

07 Service Refill Capacities Specification

Cooling System 2.6gal 9.9L
Fuel Tank 23.8gal 90.1L
Hydraulic Tank 9.2gal 34.9L
Engine Crankcase 1.8gal 6.9L
Hydraulic System 14gal 53L
Chain Box - Each Side 2.1gal 8L

08 Cab Specification

Rops SAE J1040 MAY94 and ISO3471:1994
Fops SAEJ/ISO 3449 APR98 Level I and ISO3449:1992 Level I
Fops Level Ii SAEJ/ISO 3449 APR 98 Level II and ISO 3449:1992 Level II (optional)

09 Dimensions Dimensions

Length With Bucket 11.87ft in 3616mm
Width Over Tires 6.01ft in 1829mm
Ground Clearance 9in 228.6mm
Height To Top Of Cab 6.83ft in 2080mm
Wheelbase 4.03ft in 1228mm
Length W/O Bucket 9.55ft in 2910mm
Clearance At Max Lift And Dump 7.99ft in 2435mm
Reach At Max Lift And Dump 30.71in 780mm
Bucket Pin Height - Carry Position 9.6in 243.84mm
Clearance At Maximum Lift And Dump 98.2in 2494.29mm
Length - Without Bucket 114.3in 2903.22mm
Maximum Overall Height 161in 4089.4mm
Bumper Overhang - Rear Axle 41.1in 1043.94mm
Reach - Maximum Lift/Dump 32.5in 825.5mm
Turning Radius From Center - Inc Bucket 89.14in 2264mm
Length - With Bucket On Ground 142.4in 3616.96mm
Vehicle Width Over Tires 72in 1828.8mm

10 Operating Specifications Dimensions

Breakout Force - Tilt Cylinder 5212lb 2364.13kg
Breakout Force - Lift Cylinder 5020lb 2277.04kg
Rated Operating Capacity 2250lb 1020.59kg
Rated Operating Capacity With Optional Counterweight 2300lb 1043.27kg
Tipping Load 4500lb 2041.17kg

Method. Figures are manufacturer reference specifications, not measurements. Every value is checked for unit consistency, physically possible magnitude, and plausibility for its equipment class before publication; figures that fail any check are withheld rather than shown, and figures reconstructed from related data are marked above. Imperial and metric figures are reproduced as published, except where a note states otherwise.