Specification sheet Skid Steer Loader Ref caterpillar-248-skid-steer-loader

Caterpillar 248

The Caterpillar 248 is a skid steer loader with an operating weight of 7,338 lb (3,328.5 kg), a 74 hp engine, a rated operating capacity of 2,000 lb (907.19 kg), and a tipping load of 4,000 lb (1,814.37 kg).

✓ QA-verified — every figure checked for unit consistency, physical possibility, and class plausibility; failures withheld →
Operating weight
7,338lb
3,328.5kg
Engine power
74hp
55.19kW
Net Power
Rated operating capacity
2,000lb
907.19kg
Tipping load
4,000lb
1,814.37kg
Bucket capacity
0.6yd³
0.5m³

Where it sits in its classpercentile · skid steer loaders

Among 360 skid steer loaders , the Caterpillar 248 sits above the median for its class:

  • Operating weight 7,340 lb heavier than 65% (n=334)
  • Engine power 74 hp more powerful than 69% (n=335)
  • Rated operating capacity 2,000 lb higher-rated than 56% (n=288)

Scale drawingdrawn to scale · mm

2092C229D3515A2800B
Side elevation
2092C1829E
Front elevation

01 Engine Specification

Number Of Cylinders 4
Engine Make 2236
Engine Model 3034T
Gross Power 80hp 59.7kw
Net Power 74hp 55.2kw
Power Measured @ 2600rpm
Displacement 183cu in 3L
Bore 3.9in 97.1mm
Stroke 4in 100.1mm
Engine Model Cat 3034C
Net Flywheel Power 55hp 41.1kw

02 Operational Specification

Operational Weight 7530lb 3415.6kg
Fuel Capacity 23.8gal 90L
Max Speed 7.6mph 12.1km/h
Hydraulic System Fluid Capacity 14.1gal 53L
Operating Speed 7.6mph 12.1km/h

03 Loader Specification

Operating Load Rating 2000lb 907.2kg
Bucket Capacity 0.6yd3 0.5m3

04 Weights Specification

Operating Weight 7338lb 3328.5kg

05 Hydraulic Specification

Pump Flow Capacity 33.1gal/min 125L/min

06 Hydraulic System Specification

Loader Hydraulic Pressure 4200 psi
Loader Hydraulic Flow 33 gal/min
Hydraulic Flow Standard flow

07 Service Refill Capacities Specification

Cooling System 2.6gal 9.9L
Fuel Tank 23.8gal 90.1L
Hydraulic Tank 9.2gal 34.9L
Engine Crankcase 1.8gal 6.9L
Hydraulic System 13.7gal 51.9L
Chain Box - Each Side 2gal 7.6L

08 Cab Specification

Rops SAE J1040 MAY94 and ISO3471:1994
Fops SAEJ/ISO 3449 APR98 Level I and ISO3449:1992 Level I
Fops Level Ii SAEJ/ISO 3449 APR 98 Level II and ISO 3449:1992 Level II (optional)

09 Dimensions Dimensions

Length With Bucket 11.54ft in 3515mm
Width Over Tires 6.01ft in 1829mm
Ground Clearance 9in 228.6mm
Height To Top Of Cab 6.87ft in 2092mm
Wheelbase 3.73ft in 1134mm
Length W/O Bucket 9.19ft in 2800mm
Clearance At Max Lift And Dump 7.87ft in 2398mm
Reach At Max Lift And Dump 23.39in 594mm
Bucket Pin Height - Carry Position 120in 3048mm
Clearance At Maximum Lift And Dump 94in 2387.6mm
Length - Without Bucket 110in 2794mm
Maximum Overall Height 156in 3962.4mm
Bumper Overhang - Rear Axle 41in 1041.41mm
Reach - Maximum Lift/Dump 21.3in 541.02mm
Turning Radius From Center - Inc Bucket 86.5in 2197mm
Length - With Bucket On Ground 138in 3505.2mm
Vehicle Width Over Tires 66in 1676.4mm

10 Operating Specifications Dimensions

Breakout Force - Tilt Cylinder 5261lb 2386.35kg
Breakout Force - Lift Cylinder 4308lb 1954.08kg
Rated Operating Capacity 2000lb 907.19kg
Rated Operating Capacity With Optional Counterweight 2100lb 952.55kg
Tipping Load 4000lb 1814.37kg

Method. Figures are manufacturer reference specifications, not measurements. Every value is checked for unit consistency, physically possible magnitude, and plausibility for its equipment class before publication; figures that fail any check are withheld rather than shown, and figures reconstructed from related data are marked above. Imperial and metric figures are reproduced as published, except where a note states otherwise.