Specification sheet Skid Steer Loader Ref caterpillar-236-skid-steer-loader

Caterpillar 236

The Caterpillar 236 is a skid steer loader with an operating weight of 6,810 lb (3,089 kg), a 59 hp engine, a rated operating capacity of 1,750 lb (793.79 kg), and a tipping load of 3,500 lb (1,587.58 kg).

✓ QA-verified — every figure checked for unit consistency, physical possibility, and class plausibility; failures withheld →
Operating weight
6,810lb
3,089kg
Engine power
59hp
44kW
Net Power
Rated operating capacity
1,750lb
793.79kg
Tipping load
3,500lb
1,587.58kg
Bucket capacity
0.6yd³
0.4m³

Where it sits in its classpercentile · skid steer loaders

Among 360 skid steer loaders , the Caterpillar 236 sits in the middle of its class:

  • Operating weight 6,810 lb heavier than 50% (n=334)
  • Engine power 59 hp less powerful than 57% (n=335)
  • Rated operating capacity 1,750 lb lower-rated than 61% (n=288)

Scale drawingdrawn to scale · mm

2092C229D3596A2800B
Side elevation
2092C1829E
Front elevation

01 Engine Specification

Number Of Cylinders 4
Engine Make 2236
Engine Model 3034
Gross Power 63hp 47kw
Net Power 59hp 44kw
Power Measured @ 2600rpm
Displacement 183cu in 3L
Bore 3.9in 97.1mm
Stroke 4in 100.1mm
Engine Model Cat 3034C
Net Flywheel Power 44hp 32.9kw

02 Operational Specification

Operational Weight 7030lb 3188.8kg
Fuel Capacity 23.8gal 90L
Max Speed 6.9mph 11.1km/h
Hydraulic System Fluid Capacity 13.8gal 52L
Operating Speed 7.6mph 12.1km/h

03 Loader Specification

Operating Load Rating 1750lb 793.8kg
Bucket Capacity 0.6yd3 0.4m3

04 Weights Specification

Operating Weight 6810lb 3089kg

05 Hydraulic Specification

Pump Flow Capacity 22gal/min 83L/min

06 Hydraulic System Specification

Loader Hydraulic Pressure 3300 psi
Loader Hydraulic Flow 22 gal/min
Hydraulic Flow Standard flow

07 Service Refill Capacities Specification

Cooling System 2.6gal 9.9L
Fuel Tank 23.8gal 90.1L
Hydraulic Tank 9.2gal 34.9L
Engine Crankcase 1.8gal 6.9L
Hydraulic System 13.7gal 51.9L
Chain Box - Each Side 2gal 7.6L

08 Cab Specification

Rops SAE J1040 MAY94 and ISO3471:1994
Fops SAEJ/ISO 3449 APR98 Level I and ISO3449:1992 Level I
Fops Level Ii SAEJ/ISO 3449 APR 98 Level II and ISO 3449:1992 Level II (optional)

09 Dimensions Dimensions

Length With Bucket 11.8ft in 3596mm
Width Over Tires 6.01ft in 1829mm
Ground Clearance 9in 228.6mm
Height To Top Of Cab 6.87ft in 2092mm
Wheelbase 3.73ft in 1134mm
Length W/O Bucket 9.19ft in 2800mm
Clearance At Max Lift And Dump 7.87ft in 2398mm
Reach At Max Lift And Dump 23.12in 587mm
Bucket Pin Height - Carry Position 10in 254mm
Clearance At Maximum Lift And Dump 94in 2387.6mm
Length - Without Bucket 110in 2794mm
Maximum Overall Height 156in 3962.4mm
Bumper Overhang - Rear Axle 41in 1041.41mm
Reach - Maximum Lift/Dump 21in 533.4mm
Turning Radius From Center - Inc Bucket 85.24in 2165mm
Length - With Bucket On Ground 138in 3505.2mm
Vehicle Width Over Tires 66in 1676.4mm

10 Operating Specifications Dimensions

Breakout Force - Tilt Cylinder 5255lb 2383.63kg
Breakout Force - Lift Cylinder 4344lb 1970.41kg
Rated Operating Capacity 1750lb 793.79kg
Rated Operating Capacity With Optional Counterweight 1850lb 839.15kg
Tipping Load 3500lb 1587.58kg

Method. Figures are manufacturer reference specifications, not measurements. Every value is checked for unit consistency, physically possible magnitude, and plausibility for its equipment class before publication; figures that fail any check are withheld rather than shown, and figures reconstructed from related data are marked above. Imperial and metric figures are reproduced as published, except where a note states otherwise.