Specification sheet Skid Steer Loader Ref caterpillar-232-skid-steer-loader

Caterpillar 232

The Caterpillar 232 is a skid steer loader with an operating weight of 6,739.5 lb (3,057 kg), a 48 hp engine, a rated operating capacity of 1,750 lb (793.79 kg), and a tipping load of 3,500 lb (1,587.58 kg).

✓ QA-verified — every figure checked for unit consistency, physical possibility, and class plausibility; failures withheld →
Operating weight
6,739.5lb
3,057kg
Engine power
48hp
35.8kW
Net Power
Rated operating capacity
1,750lb
793.79kg
Tipping load
3,500lb
1,587.58kg
Bucket capacity
0.6yd³
0.4m³

Where it sits in its classpercentile · skid steer loaders

Among 360 skid steer loaders , the Caterpillar 232 sits in the middle of its class:

  • Operating weight 6,740 lb lighter than 52% (n=334)
  • Engine power 48 hp less powerful than 77% (n=335)
  • Rated operating capacity 1,750 lb lower-rated than 61% (n=288)

Scale drawingdrawn to scale · mm

1950C145D3437A2760B
Side elevation
1950C1525E
Front elevation

01 Engine Specification

Number Of Cylinders 4
Engine Make 2236
Engine Model 3024C
Gross Power 51hp 38.1kw
Net Power 48hp 35.8kw
Power Measured @ 3000rpm
Displacement 134cu in 2.2L
Bore 3.4in 84.1mm
Stroke 4in 100.1mm
Engine Model Cat 3034C
Net Flywheel Power 48hp 35.8kw

02 Operational Specification

Operational Weight 6931lb 3143.9kg
Fuel Capacity 17.2gal 65L
Max Speed 6.2mph 9.9km/h
Hydraulic System Fluid Capacity 14.6gal 55L
Operating Speed 6.2mph 9.9km/h

03 Loader Specification

Operating Load Rating 1750lb 793.8kg
Bucket Capacity 0.6yd3 0.4m3

04 Weights Specification

Operating Weight 6739.5lb 3057kg

05 Hydraulic Specification

Pump Flow Capacity 14.6gal/min 55L/min

06 Hydraulic System Specification

Loader Hydraulic Pressure 3100 psi
Loader Hydraulic Flow 14.7 gal/min

07 Service Refill Capacities Specification

Cooling System 2.4gal 9.1L
Fuel Tank 18.2gal 68.9L
Hydraulic Tank 9.2gal 34.9L
Engine Crankcase 2.1gal 8L
Hydraulic System 15.3gal 58L
Chain Box - Each Side 1.6gal 6.1L

08 Cab Specification

Rops SAE J1040 MAY94 and ISO3471:1994
Fops SAEJ/ISO 3449 APR98 Level I and ISO3449:1992 Level I
Fops Level Ii SAEJ/ISO 3449 APR 98 Level II and ISO 3449:1992 Level II (optional)

09 Dimensions Dimensions

Length With Bucket 11.28ft in 3437mm
Width Over Tires 5.01ft in 1525mm
Ground Clearance 5.7in 144.78mm
Height To Top Of Cab 6.4ft in 1950mm
Wheelbase 3.59ft in 1094mm
Length W/O Bucket 9.06ft in 2760mm
Clearance At Max Lift And Dump 7.62ft in 2320mm
Reach At Max Lift And Dump 30.16in 766mm
Bucket Pin Height - Carry Position 9.7in 246.38mm
Clearance At Maximum Lift And Dump 86.9in 2207.27mm
Length - Without Bucket 109.3in 2776.22mm
Maximum Overall Height 153.31in 3893.82mm
Bumper Overhang - Rear Axle 38.9in 988.06mm
Reach - Maximum Lift/Dump 28.5in 723.9mm
Turning Radius From Center - Inc Bucket 88.71in 2253mm
Length - With Bucket On Ground 135.31in 3436.62mm
Vehicle Width Over Tires 60in 1524mm

10 Operating Specifications Dimensions

Breakout Force - Tilt Cylinder 4056lb 1839.78kg
Breakout Force - Lift Cylinder 3814lb 1730.01kg
Rated Operating Capacity 1750lb 793.79kg
Rated Operating Capacity With Optional Counterweight 1795lb 814.2kg
Tipping Load 3500lb 1587.58kg

Method. Figures are manufacturer reference specifications, not measurements. Every value is checked for unit consistency, physically possible magnitude, and plausibility for its equipment class before publication; figures that fail any check are withheld rather than shown, and figures reconstructed from related data are marked above. Imperial and metric figures are reproduced as published, except where a note states otherwise.