Case TR320
The Case TR320 is a compact track loader with an operating weight of 9,600 lb (4,354.49 kg), a 84 hp engine, a rated operating capacity of 3,200 lb (1,451.5 kg), and a tipping load of 6,400 lb (2,902.99 kg).
✓ QA-verified — every figure checked for unit consistency, physical possibility, and class plausibility; failures withheld →◆Where it sits in its classpercentile · compact track loaders
Among 184 compact track loaders , the Case TR320 sits in the middle of its class:
- Operating weight 9,600 lb heavier than 56% (n=182)
- Engine power 84 hp more powerful than 78% (n=167)
- Rated operating capacity 3,200 lb higher-rated than 70% (n=156)
◇Scale drawingdrawn to scale · mm
01 Engine Specification
| Number Of Cylinders | 4 | |
|---|---|---|
| Engine Make | 2239 | |
| Engine Model | 432T/M3 | |
| Gross Power | 90hp | 67.2kw |
| Net Power | 84hp | 62.7kw |
| Power Measured @ | 2500rpm | |
| Peak Torque | 251lb ft | 340.4Nm |
| Torque Measured @ | 1400rpm | |
| Displacement | 195cu in | 3.2L |
| Aspiration | Turbocharged |
02 Operational Specification
| Operating Weight | 9600lb | 4354.5kg |
|---|---|---|
| Fuel Capacity | 25.5gal | 96.6L |
| Engine Oil Capacity | 2.6gal | 9.5L |
| Hydraulic System Fluid Capacity | 11.8gal | 44.5L |
| Operating Voltage | 12V | |
| Alternator Supplied Amperage | 95amps | |
| Max Speed - Low Range | 5.8mph | 9.4km/h |
| Max Speed - High Range | 8.3mph | 13.4km/h |
03 Loader Specification
| Operating Load | 3200lb | 1451.5kg |
|---|---|---|
| Bucket Capacity | 0.7yd3 | 0.6m3 |
| Bucket Width | 78in | 1981.2mm |
04 Hydraulic Specification
| Pump Type | Gear | |
|---|---|---|
| Pump Flow | 12.2gal/min | 46L/min |
| Relief Valve Pressure | 3000psi | 20684.3kPa |
05 Dimensions Dimensions
| Width Over Tracks | 6.24ft in | 1900mm |
|---|---|---|
| Height To Top Of Cab | 6.57ft in | 2000mm |
| Ground Clearance | 9.57in | 243mm |
| Clearance At Max Lift And Dump | 8.54ft in | 2600mm |
| Reach At Max Lift And Dump | 1.78ft in | 540mm |
| Turning Radius From Center - Machine Rear | 70.41in | 1788.16mm |
| Length With Bucket | 11.82ft in | 3600mm |
| Length With Out Bucket | 9.85ft in | 3000mm |
| Turning Radius From Center - Inc Bucket | 85.5in | 2171.7mm |
06 Undercarriage Dimensions
| Track Gauge | 4.93ft in | 1500mm |
|---|---|---|
| Ground Contact Area | 2038in2 | 1.32m2 |
| Width Of Track | 15.75in | 400mm |
| Ground Pressure | 4.8psi | 33.1kPa |
Data notes
Derived value. tipping load was not published directly in a usable form by the source. It was reconstructed from related published figures and accepted only after validating against the expected relationship between specifications for this machine class.
Method. Figures are manufacturer reference specifications, not measurements. Every value is checked for unit consistency, physically possible magnitude, and plausibility for its equipment class before publication; figures that fail any check are withheld rather than shown, and figures reconstructed from related data are marked above. Imperial and metric figures are reproduced as published, except where a note states otherwise.