Specification sheet Skid Steer Loader Ref case-sr220-skid-steer-loader

Case SR220

The Case SR220 is a skid steer loader with an operating weight of 7,400 lb (3,356.59 kg), a 76 hp engine, a rated operating capacity of 2,200 lb (997.91 kg), and a tipping load of 4,400 lb (1,995.81 kg).

✓ QA-verified — every figure checked for unit consistency, physical possibility, and class plausibility; failures withheld →
Operating weight
7,400lb
3,356.59kg
Engine power
76hp
56.68kW
Net Power
Rated operating capacity
2,200lb
997.91kg
Tipping load
4,400lb † — value reconstructed from related published figures
1,995.81kg
Bucket capacity
0.7yd³
0.5m³

◆Where it sits in its classpercentile · skid steer loaders

Among 360 skid steer loaders , the Case SR220 sits above the median for its class:

  • Operating weight 7,400 lb heavier than 67% (n=334)
  • Engine power 76 hp more powerful than 76% (n=335)
  • Rated operating capacity 2,200 lb higher-rated than 65% (n=288)

◇Scale drawingdrawn to scale · mm

2000C203D3600A3000B
Side elevation
2000C1800E
Front elevation

01 Engine Specification

Number Of Cylinders 4
Engine Make 2239
Engine Model 432T/M3
Gross Power 82hp 61.2kw
Net Power 76hp 56.7kw
Power Measured @ 2500rpm
Max Torque 225lb ft 305.1Nm
Torque Measured @ 1400rpm
Aspiration Turbocharged
Displacement 195cu in 3.2L

02 Operational Specification

Operational Weight 7400lb 3356.6kg
Fuel Capacity 25.5gal 96.6L
Engine Oil Fluid Capacity 2.7gal 10L
Hydraulic System Fluid Capacity 6gal 22.4L
Max Speed 11.9mph 19.2km/h
Chain Box Fluid Capacity - Each Side 2gal 7.4L
Operating Speed 7.2mph 11.6km/h
Tire Size 12 x 16.5
Operating Voltage 12V
Alternator Supplied Amperage 95amps

03 Loader Specification

Operating Load Rating 2200lb 998kg
Bucket Capacity 0.7yd3 0.5m3
Bucket Width 72in 1828.8mm

04 Hydraulic Specification

Pump Type Gear
Pump Flow Capacity 12.2gal/min 46L/min
Relief Valve Pressure 3000psi 20684.3kPa

05 Dimensions Dimensions

Length With Bucket 11.82ft in 3600mm
Width Over Tires 5.91ft in 1800mm
Ground Clearance 8in 203.2mm
Height To Top Of Cab 6.57ft in 2000mm
Wheelbase 4.27ft in 1300mm
Length W/O Bucket 9.85ft in 3000mm
Clearance At Max Lift And Dump 8.54ft in 2600mm
Reach At Max Lift And Dump 19.5in 495.3mm
Turning Radius From Center - Machine Rear 70.41in 1788.16mm
Turning Radius From Center - Inc Bucket 84.2in 2138.68mm

?Questions & answersfrom this machine's data

How much does a Case SR220 skid steer weigh?
A Case SR220 skid steer has an operating weight of 7,400 lb (3,356.6 kg).
How much can a Case SR220 skid steer lift?
A Case SR220 skid steer has a rated operating capacity of 2,200 lb (997.9 kg).
What engine does a Case SR220 skid steer have?
A Case SR220 skid steer is powered by a 432T/M3 engine producing 76 hp (56.7 kW).
What is the ground clearance of a Case SR220 skid steer?
A Case SR220 skid steer has a ground clearance of 8 in (203.2 mm).
How long is a Case SR220 skid steer?
A Case SR220 skid steer has an overall length of 11.8 ft (3,600 mm) with the bucket on the ground.

Data notes

†

Derived value. tipping load was not published directly in a usable form by the source. It was reconstructed from related published figures and accepted only after validating against the expected relationship between specifications for this machine class.

Method. Figures are manufacturer reference specifications, not measurements. Every value is checked for unit consistency, physically possible magnitude, and plausibility for its equipment class before publication; figures that fail any check are withheld rather than shown, and figures reconstructed from related data are marked above. Imperial and metric figures are reproduced as published, except where a note states otherwise.