Case SR200
The Case SR200 is a skid steer loader with an operating weight of 6,900 lb (3,129.79 kg), a 70 hp engine, a rated operating capacity of 2,000 lb (907.19 kg), and a tipping load of 4,000 lb (1,814.37 kg).
✓ QA-verified — every figure checked for unit consistency, physical possibility, and class plausibility; failures withheld →◆Where it sits in its classpercentile · skid steer loaders
Among 360 skid steer loaders , the Case SR200 sits in the middle of its class:
- Operating weight 6,900 lb heavier than 53% (n=334)
- Engine power 70 hp more powerful than 59% (n=335)
- Rated operating capacity 2,000 lb higher-rated than 56% (n=288)
◇Scale drawingdrawn to scale · mm
01 Engine Specification
| Number Of Cylinders | 4 | |
|---|---|---|
| Engine Make | 2239 | |
| Engine Model | 432T/M3 | |
| Gross Power | 74hp | 55.2kw |
| Net Power | 70hp | 52.2kw |
| Power Measured @ | 2500rpm | |
| Max Torque | 203lb ft | 275.3Nm |
| Torque Measured @ | 1400rpm | |
| Aspiration | Turbocharged | |
| Displacement | 195cu in | 3.2L |
02 Operational Specification
| Operational Weight | 6900lb | 3129.8kg |
|---|---|---|
| Fuel Capacity | 20gal | 75.8L |
| Engine Oil Fluid Capacity | 2.7gal | 10L |
| Hydraulic System Fluid Capacity | 5.3gal | 20L |
| Max Speed | 11.9mph | 19.2km/h |
| Chain Box Fluid Capacity - Each Side | 1.8gal | 6.7L |
| Operating Speed | 7.2mph | 11.6km/h |
| Tire Size | 10 x 12.5 | |
| Operating Voltage | 12V | |
| Alternator Supplied Amperage | 95amps |
03 Loader Specification
| Operating Load Rating | 2000lb | 907.2kg |
|---|---|---|
| Bucket Capacity | 0.6yd3 | 0.5m3 |
| Bucket Width | 66in | 1676.4mm |
04 Hydraulic Specification
| Pump Type | Gear | |
|---|---|---|
| Pump Flow Capacity | 8.2gal/min | 31L/min |
| Relief Valve Pressure | 3000psi | 20684.3kPa |
05 Dimensions Dimensions
| Length With Bucket | 10.83ft in | 3300mm |
|---|---|---|
| Width Over Tires | 5.35ft in | 1630mm |
| Ground Clearance | 8in | 203.2mm |
| Height To Top Of Cab | 6.57ft in | 2000mm |
| Wheelbase | 3.71ft in | 1130mm |
| Length W/O Bucket | 8.76ft in | 2670mm |
| Clearance At Max Lift And Dump | 8.21ft in | 2500mm |
| Reach At Max Lift And Dump | 20.3in | 515.62mm |
| Turning Radius From Center - Machine Rear | 62.9in | 1597.66mm |
| Turning Radius From Center - Inc Bucket | 79.91in | 2029.46mm |
Data notes
Derived value. tipping load was not published directly in a usable form by the source. It was reconstructed from related published figures and accepted only after validating against the expected relationship between specifications for this machine class.
Method. Figures are manufacturer reference specifications, not measurements. Every value is checked for unit consistency, physically possible magnitude, and plausibility for its equipment class before publication; figures that fail any check are withheld rather than shown, and figures reconstructed from related data are marked above. Imperial and metric figures are reproduced as published, except where a note states otherwise.