Specification sheet Skid Steer Loader Ref case-sr150-skid-steer-loader

Case SR150

The Case SR150 is a skid steer loader with an operating weight of 5,300 lb (2,404.04 kg), a 49 hp engine, a rated operating capacity of 1,500 lb (680.39 kg), and a tipping load of 3,030 lb (1,374.39 kg).

✓ QA-verified — every figure checked for unit consistency, physical possibility, and class plausibility; failures withheld →
Operating weight
5,300lb
2,404.04kg
Engine power
49hp
36.54kW
Net Power
Rated operating capacity
1,500lb
680.39kg
Tipping load
3,030lb † — value reconstructed from related published figures
1,374.39kg
Bucket capacity
0.5yd³
0.4m³

◆Where it sits in its classpercentile · skid steer loaders

Among 360 skid steer loaders , the Case SR150 sits below the median for its class:

  • Operating weight 5,300 lb lighter than 84% (n=334)
  • Engine power 49 hp less powerful than 75% (n=335)
  • Rated operating capacity 1,500 lb lower-rated than 77% (n=288)

◇Scale drawingdrawn to scale · mm

1920C178D3030A2440B
Side elevation
1920C1520E
Front elevation

01 Engine Specification

Number Of Cylinders 4
Engine Model ISM N844T/M3
Gross Power 52hp 38.8kw
Net Power 49hp 36.6kw
Power Measured @ 2900rpm
Max Torque 109lb ft 147.8Nm
Torque Measured @ 1750rpm
Aspiration Turbocharged
Displacement 122cu in 2L

02 Operational Specification

Operational Weight 5300lb 2404.1kg
Fuel Capacity 16gal 60.6L
Engine Oil Fluid Capacity 2gal 7.5L
Hydraulic System Fluid Capacity 4gal 15.1L
Chain Box Fluid Capacity - Each Side 1.7gal 6.3L
Operating Speed 6.7mph 10.8km/h
Tire Size 10 x 16.5
Operating Voltage 12V
Alternator Supplied Amperage 120amps

03 Loader Specification

Operating Load Rating 1500lb 680.4kg
Bucket Capacity 0.5yd3 0.4m3
Bucket Width 60in 1524mm

04 Hydraulic Specification

Pump Type Gear
Pump Flow Capacity 15.6gal/min 59L/min
Relief Valve Pressure 3000psi 20684.3kPa

05 Dimensions Dimensions

Length With Bucket 9.95ft in 3030mm
Width Over Tires 4.99ft in 1520mm
Ground Clearance 7in 177.8mm
Height To Top Of Cab 6.3ft in 1920mm
Wheelbase 3.09ft in 940mm
Length W/O Bucket 8.01ft in 2440mm
Clearance At Max Lift And Dump 7.39ft in 2250mm
Reach At Max Lift And Dump 18.5in 469.9mm
Turning Radius From Center - Machine Rear 56.4in 1432.56mm
Turning Radius From Center - Inc Bucket 75.6in 1920.24mm

?Questions & answersfrom this machine's data

How much does a Case SR150 skid steer weigh?
A Case SR150 skid steer has an operating weight of 5,300 lb (2,404 kg).
How much can a Case SR150 skid steer lift?
A Case SR150 skid steer has a rated operating capacity of 1,500 lb (680.4 kg).
What engine does a Case SR150 skid steer have?
A Case SR150 skid steer is powered by a ISM N844T/M3 engine producing 49 hp (36.5 kW).
What is the ground clearance of a Case SR150 skid steer?
A Case SR150 skid steer has a ground clearance of 7 in (177.8 mm).
How long is a Case SR150 skid steer?
A Case SR150 skid steer has an overall length of 10 ft (3,030 mm) with the bucket on the ground.

Data notes

†

Derived value. tipping load was not published directly in a usable form by the source. It was reconstructed from related published figures and accepted only after validating against the expected relationship between specifications for this machine class.

Method. Figures are manufacturer reference specifications, not measurements. Every value is checked for unit consistency, physically possible magnitude, and plausibility for its equipment class before publication; figures that fail any check are withheld rather than shown, and figures reconstructed from related data are marked above. Imperial and metric figures are reproduced as published, except where a note states otherwise.