Case SR130
The Case SR130 is a skid steer loader with an operating weight of 5,000 lb (2,267.97 kg), a 43 hp engine, a rated operating capacity of 1,300 lb (589.68 kg), and a tipping load of 2,600 lb (1,179.34 kg).
✓ QA-verified — every figure checked for unit consistency, physical possibility, and class plausibility; failures withheld →◆Where it sits in its classpercentile · skid steer loaders
Among 360 skid steer loaders , the Case SR130 sits at the compact end of its class:
- Operating weight 5,000 lb lighter than 86% (n=334)
- Engine power 43 hp less powerful than 86% (n=335)
- Rated operating capacity 1,300 lb lower-rated than 88% (n=288)
◇Scale drawingdrawn to scale · mm
01 Engine Specification
| Number Of Cylinders | 4 | |
|---|---|---|
| Engine Model | ISM N844T/M3 | |
| Gross Power | 46hp | 34.4kw |
| Net Power | 43hp | 32.1kw |
| Power Measured @ | 2900rpm | |
| Max Torque | 96.3lb ft | 130.6Nm |
| Torque Measured @ | 1750rpm | |
| Aspiration | Natural | |
| Displacement | 122cu in | 2L |
02 Operational Specification
| Operational Weight | 5000lb | 2268kg |
|---|---|---|
| Fuel Capacity | 16gal | 60.6L |
| Engine Oil Fluid Capacity | 2gal | 7.5L |
| Hydraulic System Fluid Capacity | 4gal | 15.1L |
| Chain Box Fluid Capacity - Each Side | 1.7gal | 6.3L |
| Operating Speed | 6.7mph | 10.8km/h |
| Tire Size | 10 x 16.5 | |
| Operating Voltage | 12V | |
| Alternator Supplied Amperage | 120amps |
03 Loader Specification
| Operating Load Rating | 1300lb | 589.7kg |
|---|---|---|
| Bucket Capacity | 0.5yd3 | 0.4m3 |
| Bucket Width | 60in | 1524mm |
04 Hydraulic Specification
| Pump Type | Gear | |
|---|---|---|
| Pump Flow Capacity | 15.6gal/min | 59L/min |
| Relief Valve Pressure | 3000psi | 20684.3kPa |
05 Dimensions Dimensions
| Length With Bucket | 9.95ft in | 3030mm |
|---|---|---|
| Width Over Tires | 4.99ft in | 1520mm |
| Ground Clearance | 7in | 177.8mm |
| Height To Top Of Cab | 6.3ft in | 1920mm |
| Wheelbase | 3.09ft in | 940mm |
| Length W/O Bucket | 8.01ft in | 2440mm |
| Clearance At Max Lift And Dump | 7.39ft in | 2250mm |
| Reach At Max Lift And Dump | 18.5in | 469.9mm |
| Turning Radius From Center - Machine Rear | 56.4in | 1432.56mm |
| Turning Radius From Center - Inc Bucket | 75.6in | 1920.24mm |
Data notes
Derived value. tipping load was not published directly in a usable form by the source. It was reconstructed from related published figures and accepted only after validating against the expected relationship between specifications for this machine class.
Method. Figures are manufacturer reference specifications, not measurements. Every value is checked for unit consistency, physically possible magnitude, and plausibility for its equipment class before publication; figures that fail any check are withheld rather than shown, and figures reconstructed from related data are marked above. Imperial and metric figures are reproduced as published, except where a note states otherwise.