Specification sheet Wheel Loader Ref case-921c-wheel-loader
Case 921C
The Case 921C is a wheel loader with an operating weight of 50,621 lb (22,961.3 kg), a 248 hp engine, and a 4.75 yd³ (3.63 m³) bucket.
✓ QA-verified — every figure checked for unit consistency, physical possibility, and class plausibility; failures withheld → Operating weight
50,621lb
22,961.3kg
Engine power
248hp
185kW
Net Power Bucket capacity
4.75yd³
3.63m³
◆Where it sits in its classpercentile · medium wheel loaders
Among 198 medium wheel loaders (45,000–90,000 lb), the Case 921C sits below the median for its class:
- Operating weight 50,620 lb lighter than 71% (n=198)
- Engine power 248 hp less powerful than 83% (n=190)
- Bucket capacity 4.8 yd³ smaller-bucket than 86% (n=174)
◇Scale drawingdrawn to scale · mm
01 Engine Specification
| Number Of Cylinders | 6 | |
|---|---|---|
| Engine Make | 2347 | |
| Engine Model | QSMII | |
| Net Power | 248hp | 185kw |
| Gross Power | 270hp | 201.4kw |
| Power Measured @ | 2100rpm | |
| Max Torque | 926lb ft | 1255.5Nm |
| Displacement | 661cu in | 10.9L |
| Torque Measured @ | 1300rpm | |
| Aspiration | turbocharged and air to air cooled | |
| Torque Rise | 41% |
02 Operational Specification
| Operating Weight | 50621lb | 22961.3kg |
|---|---|---|
| Fuel Capacity | 104.1gal | 393.7L |
| Hydraulic System Fluid Capacity | 61.5gal | 232.8L |
| Engine Oil Fluid Capacity | 9.8gal | 36.9L |
| Cooling System Fluid Capacity | 12.5gal | 47.3L |
| Transmission Fluid Capacity | 7.6gal | 28.4L |
| Front Axle/Diff Fluid Capacity | 16.9gal | 63.6L |
| Rear Axle/Diff Fluid Capacity | 16.9gal | 63.6L |
| Static Tipping Weight | 43305.5lb | 19643kg |
| Turning Radius | 20.2ft in | 6140mm |
| Operating Voltage | 24V | |
| Alternator Supplied Amperage | 70amps | |
| Rear Axle Oscillation | 24degrees | |
| Tire Size | 26.5x25 L3 |
03 Transmission Specification
| Transmission Type | 4F/3R proportional w/ electronic control module torque sensing autoshift/manual shift and modulation | |
|---|---|---|
| Number Of Forward Gears | 4 | |
| Number Of Reverse Gears | 3 | |
| Max Speed - Forward | 24.1mph | 38.8km/h |
| Max Speed - Reverse | 16.6mph | 26.8km/h |
04 Hydraulic System Specification
| Relief Valve Setting | 2850psi | 19650.1kPa |
|---|---|---|
| Pump Flow Capacity | 38gal/min | 143.9L/min |
| Raise Time | 6.2sec | |
| Dump Time | 1.5sec | |
| Lower Time | 4.9sec | |
| Pump Type | dual, vane-type tandem |
05 Bucket Dimensions
| Dump Clearance At Max Raise | 10.34ft in | 3150mm |
|---|---|---|
| Bucket Capacity - Heaped | 4.75yd3 | 3.63m3 |
| Bucket Capacity - Struck | 3.81yd3 | 2.91m3 |
| Bucket Width | 10.01ft in | 3050mm |
| Breakout Force | 50275lb | 50275- |
06 Dimensions Dimensions
| Ground Clearance | 1.46ft in | 445mm |
|---|---|---|
| Length With Bucket On Ground | 28.06ft in | 8550mm |
| Width Over Tires | 9.65ft in | 2940mm |
| Height To Top Of Cab | 11.72ft in | 3570mm |
| Wheelbase | 11.16ft in | 3400mm |
| Hinge Pin - Max Height | 14.05ft in | 4280mm |
| Reach At Max Lift And Dump | 3.61ft in | 1100mm |
Method. Figures are manufacturer reference specifications, not measurements. Every value is checked for unit consistency, physically possible magnitude, and plausibility for its equipment class before publication; figures that fail any check are withheld rather than shown, and figures reconstructed from related data are marked above. Imperial and metric figures are reproduced as published, except where a note states otherwise.