Specification sheet Wheel Loader Ref case-821e-wheel-loader
Case 821E
The Case 821E is a wheel loader with an operating weight of 37,844 lb (17,166 kg), a 198 hp engine, and a 4.43 yd³ (3.39 m³) bucket.
✓ QA-verified — every figure checked for unit consistency, physical possibility, and class plausibility; failures withheld → Operating weight
37,844lb
17,166kg
Engine power
198hp
148kW
Net Power Bucket capacity
4.43yd³
3.39m³
◆Where it sits in its classpercentile · small wheel loaders
Among 439 small wheel loaders (22,000–45,000 lb), the Case 821E sits above the median for its class:
- Operating weight 37,840 lb heavier than 76% (n=439)
- Engine power 198 hp more powerful than 75% (n=408)
- Bucket capacity 4.4 yd³ larger-bucket than 90% (n=387)
◇Scale drawingdrawn to scale · mm
01 Engine Specification
| Number Of Cylinders | 6 | |
|---|---|---|
| Engine Make | 2239 | |
| Engine Model | Family IV, 667TA/EBD Tier III Certified | |
| Net Power | 198hp | 148kw |
| Gross Power | 210hp | 157kw |
| Power Measured @ | 1800rpm | |
| Max Torque | 724lb ft | 981.7Nm |
| Displacement | 411cu in | 6.7L |
| Torque Measured @ | 1400rpm | |
| Aspiration | Turbocharged and Aftercooled |
02 Operational Specification
| Operating Weight | 37844lb | 17166kg |
|---|---|---|
| Fuel Capacity | 76gal | 288L |
| Hydraulic System Fluid Capacity | 46gal | 174L |
| Engine Oil Fluid Capacity | 5.6gal | 21L |
| Transmission Fluid Capacity | 10.5gal | 39.7L |
| Front Axle/Diff Fluid Capacity | 9.9gal | 37.4L |
| Rear Axle/Diff Fluid Capacity | 6.3gal | 23.7L |
| Static Tipping Weight | 31376lb | 14232kg |
| Turning Radius | 19.8ft in | 6030mm |
| Operating Voltage | 24V | |
| Alternator Supplied Amperage | 70amps | |
| Rear Axle Oscillation | 24degrees | |
| Tire Size | 23.5 x 25 l2 bias |
03 Transmission Specification
| Transmission Type | 4F/3R Proportional w/Electronic Control Module | |
|---|---|---|
| Number Of Forward Gears | 4 | |
| Number Of Reverse Gears | 3 | |
| Max Speed - Forward | 23mph | 37km/h |
| Max Speed - Reverse | 15.7mph | 25.3km/h |
04 Hydraulic System Specification
| Relief Valve Setting | 3600psi | 24821kPa |
|---|---|---|
| Pump Flow Capacity | 31.6gal/min | 119.6L/min |
| Raise Time | 5.6sec | |
| Dump Time | 1.2sec | |
| Lower Time | 2.8sec | |
| Pump Type | closed centered pressure/flow compensated |
05 Bucket Dimensions
| Dump Clearance At Max Raise | 9.72ft in | 2960mm |
|---|---|---|
| Bucket Capacity - Heaped | 4.43yd3 | 3.39m3 |
| Bucket Capacity - Struck | 3.78yd3 | 2.89m3 |
| Bucket Width | 9.6ft in | 2930mm |
| Breakout Force | 34416lb | 153.09kN |
06 Dimensions Dimensions
| Ground Clearance | 1.37ft in | 415.8mm |
|---|---|---|
| Length With Bucket On Ground | 25.9ft in | 7890mm |
| Width Over Tires | 9.47ft in | 2890mm |
| Height To Top Of Cab | 11.4ft in | 3450mm |
| Wheelbase | 10.98ft in | 3340mm |
| Hinge Pin - Max Height | 13.51ft in | 4120mm |
| Reach At Max Lift And Dump | 3.71ft in | 1130mm |
Method. Figures are manufacturer reference specifications, not measurements. Every value is checked for unit consistency, physically possible magnitude, and plausibility for its equipment class before publication; figures that fail any check are withheld rather than shown, and figures reconstructed from related data are marked above. Imperial and metric figures are reproduced as published, except where a note states otherwise.