Specification sheet Wheel Loader Ref case-821c-wheel-loader
Case 821C
The Case 821C is a wheel loader with an operating weight of 37,901 lb (17,191.61 kg), a 186 hp engine, and a 3.51 yd³ (2.68 m³) bucket.
✓ QA-verified — every figure checked for unit consistency, physical possibility, and class plausibility; failures withheld → Operating weight
37,901lb
17,191.61kg
Engine power
186hp
138.8kW
Net Power Bucket capacity
3.51yd³
2.68m³
◆Where it sits in its classpercentile · small wheel loaders
Among 439 small wheel loaders (22,000–45,000 lb), the Case 821C sits above the median for its class:
- Operating weight 37,900 lb heavier than 76% (n=439)
- Engine power 186 hp more powerful than 69% (n=408)
- Bucket capacity 3.5 yd³ larger-bucket than 60% (n=387)
◇Scale drawingdrawn to scale · mm
01 Engine Specification
| Number Of Cylinders | 6 | |
|---|---|---|
| Engine Make | 2239 | |
| Engine Model | 6TAA-8304 | |
| Net Power | 186hp | 138.8kw |
| Gross Power | 204hp | 152.2kw |
| Power Measured @ | 2000rpm | |
| Max Torque | 671lb ft | 909.8Nm |
| Displacement | 504cu in | 8.3L |
| Torque Measured @ | 1400rpm | |
| Aspiration | turbocharged and air to air cooled | |
| Torque Rise | 51% |
02 Operational Specification
| Operating Weight | 37901lb | 17191.7kg |
|---|---|---|
| Fuel Capacity | 70.8gal | 268L |
| Hydraulic System Fluid Capacity | 46gal | 174L |
| Engine Oil Fluid Capacity | 5.6gal | 21L |
| Cooling System Fluid Capacity | 8.5gal | 32L |
| Transmission Fluid Capacity | 3.2gal | 12L |
| Front Axle/Diff Fluid Capacity | 8.8gal | 33L |
| Rear Axle/Diff Fluid Capacity | 7.1gal | 26.5L |
| Static Tipping Weight | 30082.1lb | 13645kg |
| Turning Radius | 18.9ft in | 5750mm |
| Operating Voltage | 24V | |
| Alternator Supplied Amperage | 65amps | |
| Rear Axle Oscillation | 24degrees | |
| Tire Size | 23.5-25 L3 |
03 Transmission Specification
| Transmission Type | 4F/3R proportional w/ electronic control module torque sensing autoshift/manual shift and modulation | |
|---|---|---|
| Number Of Forward Gears | 4 | |
| Number Of Reverse Gears | 3 | |
| Max Speed - Forward | 23.5mph | 37.9km/h |
| Max Speed - Reverse | 16.6mph | 26.8km/h |
04 Hydraulic System Specification
| Relief Valve Setting | 2813.8psi | 19400kPa |
|---|---|---|
| Pump Flow Capacity | 50gal/min | 189L/min |
| Raise Time | 5.9sec | |
| Dump Time | 1.6sec | |
| Lower Time | 4.3sec | |
| Pump Type | dual, vane-type tandem |
05 Bucket Dimensions
| Dump Clearance At Max Raise | 9.75ft in | 2970mm |
|---|---|---|
| Bucket Capacity - Heaped | 3.51yd3 | 2.68m3 |
| Bucket Capacity - Struck | 3.04yd3 | 2.32m3 |
| Bucket Width | 9.09ft in | 2770mm |
| Breakout Force | 36391lb | 36391- |
06 Dimensions Dimensions
| Ground Clearance | 1.32ft in | 401mm |
|---|---|---|
| Length With Bucket On Ground | 24.51ft in | 7470mm |
| Width Over Tires | 8.86ft in | 2700mm |
| Height To Top Of Cab | 10.93ft in | 3330mm |
| Wheelbase | 10.5ft in | 3200mm |
| Hinge Pin - Max Height | 12.96ft in | 3950mm |
| Reach At Max Lift And Dump | 3.65ft in | 1110mm |
Method. Figures are manufacturer reference specifications, not measurements. Every value is checked for unit consistency, physically possible magnitude, and plausibility for its equipment class before publication; figures that fail any check are withheld rather than shown, and figures reconstructed from related data are marked above. Imperial and metric figures are reproduced as published, except where a note states otherwise.