Specification sheet Skid Steer Loader Ref case-75xt-skid-steer-loader

Case 75XT

The Case 75XT is a skid steer loader with an operating weight of 6,700 lb (3,039.07 kg), a 69 hp engine, a rated operating capacity of 2,200 lb (997.91 kg), and a tipping load of 4,400 lb (1,995.81 kg).

✓ QA-verified — every figure checked for unit consistency, physical possibility, and class plausibility; failures withheld →
Operating weight
6,700lb
3,039.07kg
Engine power
69hp
51.46kW
Net Power
Rated operating capacity
2,200lb
997.91kg
Tipping load
4,400lb † — value reconstructed from related published figures
1,995.81kg
Bucket capacity
0.7yd³
0.5m³

◆Where it sits in its classpercentile · skid steer loaders

Among 360 skid steer loaders , the Case 75XT sits in the middle of its class:

  • Operating weight 6,700 lb lighter than 53% (n=334)
  • Engine power 69 hp more powerful than 57% (n=335)
  • Rated operating capacity 2,200 lb higher-rated than 65% (n=288)

◇Scale drawingdrawn to scale · mm

2030C226D3340A2620B
Side elevation
2030C1830E
Front elevation

01 Engine Specification

Number Of Cylinders 4
Engine Make 2239
Engine Model 4-390
Gross Power 75hp 56kw
Net Power 69hp 51.5kw
Power Measured @ 2200rpm
Aspiration Natural
Displacement 239cu in 4L

02 Operational Specification

Operational Weight 6700lb 3039.1kg
Fuel Capacity 17.3gal 65.5L
Cooling System Fluid Capacity 4.3gal 16.1L
Engine Oil Fluid Capacity 2.8gal 10.4L
Max Speed 7.2mph 11.6km/h
Hydraulic System Fluid Capacity 16.6gal 62.5L
Chain Box Fluid Capacity - Each Side 1.3gal 4.7L
Tire Size 12.00x16.5
Operating Voltage 12V
Alternator Supplied Amperage 65amps

03 Loader Specification

Breakout Force 5173lb 2346.5kg
Operating Load Rating 2200lb 998kg
Bucket Capacity 0.7yd3 0.5m3

04 Hydraulic Specification

Pump Type gear pump
Pump Flow Capacity 21gal/min 79.5L/min

05 Dimensions Dimensions

Length With Bucket 10.96ft in 3340mm
Width Over Tires 6.01ft in 1830mm
Ground Clearance 8.9in 226mm
Height To Top Of Cab 6.67ft in 2030mm
Wheelbase 3.75ft in 1140mm
Length W/O Bucket 8.6ft in 2620mm
Clearance At Max Lift And Dump 7.55ft in 2300mm
Reach At Max Lift And Dump 29.93in 760mm
Turning Radius From Center - Machine Rear 61.03in 1550mm
Turning Radius From Center - Inc Bucket 78.75in 2000mm

Data notes

†

Derived value. tipping load was not published directly in a usable form by the source. It was reconstructed from related published figures and accepted only after validating against the expected relationship between specifications for this machine class.

Method. Figures are manufacturer reference specifications, not measurements. Every value is checked for unit consistency, physically possible magnitude, and plausibility for its equipment class before publication; figures that fail any check are withheld rather than shown, and figures reconstructed from related data are marked above. Imperial and metric figures are reproduced as published, except where a note states otherwise.