Specification sheet Skid Steer Loader Ref case-60xt-skid-steer-loader

Case 60XT

The Case 60XT is a skid steer loader with an operating weight of 6,562 lb (2,976.48 kg), a 69 hp engine, a rated operating capacity of 1,800 lb (816.47 kg), and a tipping load of 3,600 lb (1,632.93 kg).

✓ QA-verified — every figure checked for unit consistency, physical possibility, and class plausibility; failures withheld →
Operating weight
6,562lb
2,976.48kg
Engine power
69hp
51.46kW
Net Power
Rated operating capacity
1,800lb
816.47kg
Tipping load
3,600lb † — value reconstructed from related published figures
1,632.93kg
Bucket capacity
0.6yd³
0.5m³

◆Where it sits in its classpercentile · skid steer loaders

Among 360 skid steer loaders , the Case 60XT sits in the middle of its class:

  • Operating weight 6,560 lb lighter than 56% (n=334)
  • Engine power 69 hp more powerful than 57% (n=335)
  • Rated operating capacity 1,800 lb lower-rated than 55% (n=288)

◇Scale drawingdrawn to scale · mm

1950C229D3230A2640B
Side elevation
1950C1630E
Front elevation

01 Engine Specification

Number Of Cylinders 4
Engine Make 2239
Engine Model 4-390
Gross Power 75hp 56kw
Net Power 69hp 51.5kw
Power Measured @ 2200rpm
Aspiration Natural
Displacement 239cu in 4L

02 Operational Specification

Operational Weight 6562lb 2976.5kg
Fuel Capacity 22gal 83.3L
Cooling System Fluid Capacity 4.4gal 16.6L
Engine Oil Fluid Capacity 2.8gal 10.4L
Max Speed 7.1mph 11.3km/h
Hydraulic System Fluid Capacity 13.3gal 50.2L
Chain Box Fluid Capacity - Each Side 1.6gal 5.7L
Tire Size 12.00x16.5
Operating Voltage 12V
Alternator Supplied Amperage 65amps

03 Loader Specification

Breakout Force 4431lb 2009.9kg
Operating Load Rating 1800lb 816.5kg
Bucket Capacity 0.6yd3 0.5m3

04 Hydraulic Specification

Pump Type gear pump
Pump Flow Capacity 21gal/min 79.5L/min

05 Dimensions Dimensions

Length With Bucket 10.6ft in 3230mm
Width Over Tires 5.35ft in 1630mm
Ground Clearance 9.02in 229mm
Height To Top Of Cab 6.4ft in 1950mm
Wheelbase 3.61ft in 1100mm
Length W/O Bucket 8.67ft in 2640mm
Clearance At Max Lift And Dump 8.04ft in 2450mm
Reach At Max Lift And Dump 21.26in 540mm
Turning Radius From Center - Machine Rear 59.06in 1500mm
Turning Radius From Center - Inc Bucket 76.78in 1950mm

Data notes

†

Derived value. tipping load was not published directly in a usable form by the source. It was reconstructed from related published figures and accepted only after validating against the expected relationship between specifications for this machine class.

Method. Figures are manufacturer reference specifications, not measurements. Every value is checked for unit consistency, physically possible magnitude, and plausibility for its equipment class before publication; figures that fail any check are withheld rather than shown, and figures reconstructed from related data are marked above. Imperial and metric figures are reproduced as published, except where a note states otherwise.