Case 465
The Case 465 is a skid steer loader with an operating weight of 8,910 lb (4,042 kg), a 82 hp engine, a rated operating capacity of 3,000 lb (1,364 kg), and a tipping load of 6,000 lb (2,721.56 kg).
✓ QA-verified — every figure checked for unit consistency, physical possibility, and class plausibility; failures withheld →◆Where it sits in its classpercentile · skid steer loaders
Among 360 skid steer loaders , the Case 465 sits at the heavy end of its class:
- Operating weight 8,910 lb heavier than 92% (n=334)
- Engine power 82 hp more powerful than 82% (n=335)
- Rated operating capacity 3,000 lb higher-rated than 91% (n=288)
◇Scale drawingdrawn to scale · mm
01 Engine Specification
| Number Of Cylinders | 4 | |
|---|---|---|
| Engine Make | 2239 | |
| Engine Model | Family III 445T/M2, Tier II certified | |
| Gross Power | 88hp | 65.7kw |
| Net Power | 82hp | 61.2kw |
| Power Measured @ | 2300rpm | |
| Aspiration | turbocharged | |
| Displacement | 274cu in | 4.5L |
02 Operational Specification
| Operational Weight | 8910lb | 4042kg |
|---|---|---|
| Fuel Capacity | 20.2gal | 76.4L |
| Cooling System Fluid Capacity | 4.5gal | 17L |
| Engine Oil Fluid Capacity | 3.2gal | 12L |
| Max Speed | 12.3mph | 19.8km/h |
| Hydraulic System Fluid Capacity | 17.5gal | 66.2L |
| Chain Box Fluid Capacity - Each Side | 2gal | 7.6L |
| Tire Size | 12.00 x 16.5 | |
| Operating Voltage | 95V | |
| Alternator Supplied Amperage | 12amps |
03 Loader Specification
| Breakout Force | 6175lb | -- |
|---|---|---|
| Operating Load Rating | 3000lb | 1364kg |
| Bucket Capacity | 0.8yd3 | 0.6m3 |
04 Hydraulic Specification
| Pump Type | Gear pump | |
|---|---|---|
| Pump Flow Capacity | 22.1gal/min | 83.9L/min |
| Relief Valve Pressure | 3000psi | 20684.3kPa |
05 Dimensions Dimensions
| Length With Bucket | 11.92ft in | 3630mm |
|---|---|---|
| Width Over Tires | 5.38ft in | 1640mm |
| Ground Clearance | 9.1in | 231mm |
| Height To Top Of Cab | 6.67ft in | 2030mm |
| Wheelbase | 4.21ft in | 1280mm |
| Length W/O Bucket | 9.23ft in | 2810mm |
| Clearance At Max Lift And Dump | 7.92ft in | 2410mm |
| Reach At Max Lift And Dump | 36.8in | 935mm |
| Turning Radius From Center - Machine Rear | 65.1in | 1650mm |
| Turning Radius From Center - Inc Bucket | 86.3in | 2190mm |
Data notes
Derived value. tipping load was not published directly in a usable form by the source. It was reconstructed from related published figures and accepted only after validating against the expected relationship between specifications for this machine class.
Method. Figures are manufacturer reference specifications, not measurements. Every value is checked for unit consistency, physically possible magnitude, and plausibility for its equipment class before publication; figures that fail any check are withheld rather than shown, and figures reconstructed from related data are marked above. Imperial and metric figures are reproduced as published, except where a note states otherwise.