Case 445CT
The Case 445CT is a compact track loader with an operating weight of 9,815 lb (4,452 kg), a 74 hp engine, a rated operating capacity of 3,500 lb (1,588 kg), and a tipping load of 7,000 lb (3,175.15 kg).
✓ QA-verified — every figure checked for unit consistency, physical possibility, and class plausibility; failures withheld →◆Where it sits in its classpercentile · compact track loaders
Among 184 compact track loaders , the Case 445CT sits above the median for its class:
- Operating weight 9,820 lb heavier than 61% (n=182)
- Engine power 74 hp more powerful than 54% (n=167)
- Rated operating capacity 3,500 lb higher-rated than 78% (n=156)
◇Scale drawingdrawn to scale · mm
01 Engine Specification
| Number Of Cylinders | 4 | |
|---|---|---|
| Engine Make | 2239 | |
| Engine Model | Family III 445/M2 | |
| Gross Power | 80.5hp | 60kw |
| Net Power | 74hp | 55.2kw |
| Power Measured @ | 2300rpm | |
| Peak Torque | 236lb ft | 320Nm |
| Torque Measured @ | 1400rpm | |
| Displacement | 274cu in | 4.5L |
| Aspiration | Natural |
02 Operational Specification
| Operating Weight | 9815lb | 4452kg |
|---|---|---|
| Cooling System Fluid Capacity | 4.5gal | 17L |
| Fuel Capacity | 17.3gal | 65.5L |
| Engine Oil Capacity | 3.2gal | 12L |
| Hydraulic System Fluid Capacity | 11gal | 41.5L |
| Operating Voltage | 12V | |
| Alternator Supplied Amperage | 95amps | |
| Max Speed - Low Range | 5.1mph | 8.2km/h |
| Max Speed - High Range | 8mph | 12.8km/h |
03 Loader Specification
| Breakout Force | 5167lb | 2343.7kg |
|---|---|---|
| Operating Load | 3500lb | 1588kg |
| Bucket Capacity | 0.8yd3 | 0.6m3 |
04 Hydraulic Specification
| Pump Type | gear pump | |
|---|---|---|
| Pump Flow | 21gal/min | 80L/min |
| Relief Valve Pressure | 3000psi | 20684.3kPa |
05 Dimensions Dimensions
| Width Over Tracks | 6.88ft in | 2098mm |
|---|---|---|
| Height To Top Of Cab | 6.67ft in | 2030mm |
| Ground Clearance | 9in | 229mm |
| Clearance At Max Lift And Dump | 7.69ft in | 2340mm |
| Reach At Max Lift And Dump | 2.81ft in | 860mm |
| Turning Radius From Center - Machine Rear | 61.1in | 1550mm |
| Length With Bucket | 11.29ft in | 3440mm |
| Turning Radius From Center - Inc Bucket | 84in | 2130mm |
| Length With Out Bucket | 8.59ft in | 2620mm |
06 Undercarriage Dimensions
| Length Of Track On Ground | 5.39ft in | 1645mm |
|---|---|---|
| Track Gauge | 5.45ft in | 1661mm |
| Ground Contact Area | 2293in2 | 1.38m2 |
| Number Of Track Rollers Per Side | 4 | |
| Width Of Track | 17.72in | 450mm |
| Ground Pressure | 4.3psi | 27.6kPa |
Data notes
Derived value. tipping load was not published directly in a usable form by the source. It was reconstructed from related published figures and accepted only after validating against the expected relationship between specifications for this machine class.
Method. Figures are manufacturer reference specifications, not measurements. Every value is checked for unit consistency, physically possible magnitude, and plausibility for its equipment class before publication; figures that fail any check are withheld rather than shown, and figures reconstructed from related data are marked above. Imperial and metric figures are reproduced as published, except where a note states otherwise.