Case 445 Series III
The Case 445 Series III is a skid steer loader with an operating weight of 8,119.63 lb (3,683 kg), a 76.44 hp engine, a rated operating capacity of 2,500.05 lb (1,134 kg), and a tipping load of 5,000.1 lb (2,268.01 kg).
✓ QA-verified — every figure checked for unit consistency, physical possibility, and class plausibility; failures withheld →◆Where it sits in its classpercentile · skid steer loaders
Among 360 skid steer loaders , the Case 445 Series III sits above the median for its class:
- Operating weight 8,120 lb heavier than 82% (n=334)
- Engine power 76 hp more powerful than 77% (n=335)
- Rated operating capacity 2,500 lb higher-rated than 81% (n=288)
◇Scale drawingdrawn to scale · mm
01 Engine Specification
| Number Of Cylinders | 4 | |
|---|---|---|
| Engine Make | 2239 | |
| Engine Model | 432T/M3 diesel Tier III certified | |
| Gross Power | 81.9hp | 61kw |
| Net Power | 76.5hp | 57kw |
| Power Measured @ | 2300rpm | |
| Aspiration | Turbocharged | |
| Displacement | 195.3cu in | 3.2L |
02 Operational Specification
| Operational Weight | 8119.7lb | 3683kg |
|---|---|---|
| Fuel Capacity | 17.4gal | 65.5L |
| Cooling System Fluid Capacity | 3.1gal | 11.4L |
| Engine Oil Fluid Capacity | 2.3gal | 8.5L |
| Max Speed | 7mph | 11.2km/h |
| Hydraulic System Fluid Capacity | 11gal | 41.6L |
| Chain Box Fluid Capacity - Each Side | 2.1gal | 7.6L |
| Operating Speed | 7mph | 11.2km/h |
| Tire Size | 12.00 x 16.5 10 ply | |
| Operating Voltage | 12V | |
| Alternator Supplied Amperage | 95amps |
03 Loader Specification
| Breakout Force | 5000lb | 2268kg |
|---|---|---|
| Operating Load Rating | 2500.1lb | 1134kg |
| Bucket Capacity | 0.6yd3 | 0.4m3 |
04 Hydraulic Specification
| Pump Type | Gear | |
|---|---|---|
| Pump Flow Capacity | 23.9gal/min | 90.1L/min |
| Relief Valve Pressure | 3050psi | 21029kPa |
05 Dimensions Dimensions
| Length With Bucket | 10.96ft in | 3340mm |
|---|---|---|
| Width Over Tires | 6.01ft in | 1830mm |
| Ground Clearance | 9.3in | 236mm |
| Height To Top Of Cab | 6.93ft in | 2110mm |
| Wheelbase | 3.75ft in | 1140mm |
| Length W/O Bucket | 8.7ft in | 2650mm |
| Clearance At Max Lift And Dump | 7.52ft in | 2290mm |
| Reach At Max Lift And Dump | 36.62in | 930mm |
| Turning Radius From Center - Machine Rear | 53.55in | 1360mm |
| Turning Radius From Center - Inc Bucket | 83.47in | 2120mm |
?Questions & answersfrom this machine's data
- How much does a Case 445 Series III skid steer weigh?
- A Case 445 Series III skid steer has an operating weight of 8,119.6 lb (3,683 kg).
- How much can a Case 445 Series III skid steer lift?
- A Case 445 Series III skid steer has a rated operating capacity of 2,500.1 lb (1,134 kg).
- What engine does a Case 445 Series III skid steer have?
- A Case 445 Series III skid steer is powered by a 432T/M3 diesel Tier III certified engine producing 76.4 hp (57 kW).
- What is the ground clearance of a Case 445 Series III skid steer?
- A Case 445 Series III skid steer has a ground clearance of 9.3 in (236 mm).
- How long is a Case 445 Series III skid steer?
- A Case 445 Series III skid steer has an overall length of 11 ft (3,340 mm) with the bucket on the ground.
Data notes
Derived value. tipping load was not published directly in a usable form by the source. It was reconstructed from related published figures and accepted only after validating against the expected relationship between specifications for this machine class.
Method. Figures are manufacturer reference specifications, not measurements. Every value is checked for unit consistency, physically possible magnitude, and plausibility for its equipment class before publication; figures that fail any check are withheld rather than shown, and figures reconstructed from related data are marked above. Imperial and metric figures are reproduced as published, except where a note states otherwise.