Case 440CT Series 3
The Case 440CT Series 3 is a compact track loader with an operating weight of 8,925 lb (4,048.32 kg), a 83 hp engine, a rated operating capacity of 3,000 lb (1,360.78 kg), and a tipping load of 6,000 lb (2,721.56 kg).
✓ QA-verified — every figure checked for unit consistency, physical possibility, and class plausibility; failures withheld →◆Where it sits in its classpercentile · compact track loaders
Among 184 compact track loaders , the Case 440CT Series 3 sits in the middle of its class:
- Operating weight 8,930 lb lighter than 59% (n=182)
- Engine power 83 hp more powerful than 72% (n=167)
- Rated operating capacity 3,000 lb higher-rated than 63% (n=156)
◇Scale drawingdrawn to scale · mm
01 Engine Specification
| Number Of Cylinders | 4 | |
|---|---|---|
| Engine Make | 2239 | |
| Engine Model | 445T/M3 | |
| Gross Power | 90hp | 67.2kw |
| Net Power | 83hp | 61.9kw |
| Power Measured @ | 2300rpm | |
| Peak Torque | 288lb ft | 390.5Nm |
| Torque Measured @ | 1300rpm | |
| Displacement | 274cu in | 4.5L |
| Aspiration | Turbocharged |
02 Operational Specification
| Operating Weight | 8925lb | 4048.4kg |
|---|---|---|
| Cooling System Fluid Capacity | 3gal | 11.4L |
| Fuel Capacity | 23.3gal | 88.3L |
| Engine Oil Capacity | 3.2gal | 12L |
| Hydraulic System Fluid Capacity | 7.1gal | 26.9L |
| Operating Voltage | 12V | |
| Alternator Supplied Amperage | 95amps | |
| Max Speed - Low Range | 5.1mph | 8.3km/h |
| Max Speed - High Range | 8mph | 12.9km/h |
03 Loader Specification
| Operating Load | 3000lb | 1360.8kg |
|---|---|---|
| Bucket Capacity | 0.7yd3 | 0.5m3 |
04 Hydraulic Specification
| Pump Type | Gear | |
|---|---|---|
| Pump Flow | 22gal/min | 83L/min |
05 Dimensions Dimensions
| Width Over Tracks | 5.95ft in | 1812mm |
|---|---|---|
| Height To Top Of Cab | 6.73ft in | 2050mm |
| Ground Clearance | 9.3in | 236mm |
| Clearance At Max Lift And Dump | 7.98ft in | 2430mm |
| Reach At Max Lift And Dump | 2.04ft in | 620mm |
| Turning Radius From Center - Inc Bucket | 79.53in | 2020mm |
| Turning Radius From Center - Machine Rear | 57.09in | 1450mm |
| Length With Bucket | 10.8ft in | 3290mm |
| Length With Out Bucket | 8.54ft in | 2600mm |
06 Undercarriage Dimensions
| Length Of Track On Ground | 4.72ft in | 1438mm |
|---|---|---|
| Ground Contact Area | 1780in2 | 1.15m2 |
| Number Of Track Rollers Per Side | 3 | |
| Width Of Track | 15.75in | 400mm |
| Ground Pressure | 5psi | 34.48kPa |
Data notes
Derived value. tipping load was not published directly in a usable form by the source. It was reconstructed from related published figures and accepted only after validating against the expected relationship between specifications for this machine class.
Method. Figures are manufacturer reference specifications, not measurements. Every value is checked for unit consistency, physically possible magnitude, and plausibility for its equipment class before publication; figures that fail any check are withheld rather than shown, and figures reconstructed from related data are marked above. Imperial and metric figures are reproduced as published, except where a note states otherwise.