Case 440CT
The Case 440CT is a compact track loader with an operating weight of 8,915 lb (4,043 kg), a 82 hp engine, a rated operating capacity of 3,000 lb (1,361 kg), and a tipping load of 6,000 lb (2,721.56 kg).
✓ QA-verified — every figure checked for unit consistency, physical possibility, and class plausibility; failures withheld →◆Where it sits in its classpercentile · compact track loaders
Among 184 compact track loaders , the Case 440CT sits in the middle of its class:
- Operating weight 8,920 lb lighter than 59% (n=182)
- Engine power 82 hp more powerful than 68% (n=167)
- Rated operating capacity 3,000 lb higher-rated than 63% (n=156)
◇Scale drawingdrawn to scale · mm
01 Engine Specification
| Number Of Cylinders | 4 | |
|---|---|---|
| Engine Make | 2239 | |
| Engine Model | Family III 445T/M2 | |
| Gross Power | 89hp | 66kw |
| Net Power | 82hp | 61kw |
| Power Measured @ | 2300rpm | |
| Peak Torque | 263lb ft | 357Nm |
| Torque Measured @ | 1400rpm | |
| Displacement | 274cu in | 4.5L |
| Aspiration | turbocharged |
02 Operational Specification
| Operating Weight | 8915lb | 4043kg |
|---|---|---|
| Cooling System Fluid Capacity | 4.5gal | 17L |
| Fuel Capacity | 22gal | 83.3L |
| Engine Oil Capacity | 3.2gal | 12L |
| Hydraulic System Fluid Capacity | 13.2gal | 50L |
| Operating Voltage | 12V | |
| Alternator Supplied Amperage | 95amps | |
| Max Speed - Low Range | 5.1mph | 8.2km/h |
| Max Speed - High Range | 7.6mph | 12.2km/h |
03 Loader Specification
| Breakout Force | 6207lb | 2815kg |
|---|---|---|
| Operating Load | 3000lb | 1361kg |
| Bucket Capacity | 0.7yd3 | 0.5m3 |
04 Hydraulic Specification
| Pump Type | gear pump | |
|---|---|---|
| Pump Flow | 21.9gal/min | 83L/min |
| Relief Valve Pressure | 3000psi | 20684.3kPa |
05 Dimensions Dimensions
| Width Over Tracks | 5.92ft in | 1802mm |
|---|---|---|
| Height To Top Of Cab | 6.39ft in | 1950mm |
| Ground Clearance | 9in | 229mm |
| Clearance At Max Lift And Dump | 8.06ft in | 2450mm |
| Reach At Max Lift And Dump | 1.95ft in | 590mm |
| Turning Radius From Center - Machine Rear | 58in | 1480mm |
| Length With Bucket | 10.6ft in | 3230mm |
| Turning Radius From Center - Inc Bucket | 80.41in | 2040mm |
| Length With Out Bucket | 8.66ft in | 2640mm |
06 Undercarriage Dimensions
| Length Of Track On Ground | 4.71ft in | 1436mm |
|---|---|---|
| Track Gauge | 4.6ft in | 1400mm |
| Ground Contact Area | 1780in2 | 1.15m2 |
| Number Of Track Rollers Per Side | 3 | |
| Width Of Track | 15.75in | 400mm |
| Ground Pressure | 5psi | 34.5kPa |
Data notes
Derived value. tipping load was not published directly in a usable form by the source. It was reconstructed from related published figures and accepted only after validating against the expected relationship between specifications for this machine class.
Method. Figures are manufacturer reference specifications, not measurements. Every value is checked for unit consistency, physically possible magnitude, and plausibility for its equipment class before publication; figures that fail any check are withheld rather than shown, and figures reconstructed from related data are marked above. Imperial and metric figures are reproduced as published, except where a note states otherwise.