Case 435
The Case 435 is a skid steer loader with an operating weight of 6,830 lb (3,098 kg), a 72 hp engine, a rated operating capacity of 2,300 lb (1,043 kg), and a tipping load of 4,600 lb (2,086.53 kg).
✓ QA-verified — every figure checked for unit consistency, physical possibility, and class plausibility; failures withheld →◆Where it sits in its classpercentile · skid steer loaders
Among 360 skid steer loaders , the Case 435 sits in the middle of its class:
- Operating weight 6,830 lb heavier than 51% (n=334)
- Engine power 72 hp more powerful than 63% (n=335)
- Rated operating capacity 2,300 lb higher-rated than 70% (n=288)
◇Scale drawingdrawn to scale · mm
01 Engine Specification
| Number Of Cylinders | 3 | |
|---|---|---|
| Engine Make | 2239 | |
| Engine Model | Family III 334T/M2, Tier II certified | |
| Gross Power | 78hp | 58kw |
| Net Power | 72hp | 54kw |
| Power Measured @ | 2300rpm | |
| Aspiration | turbocharged | |
| Displacement | 205cu in | 3.4L |
02 Operational Specification
| Operational Weight | 6830lb | 3098kg |
|---|---|---|
| Fuel Capacity | 17.5gal | 66L |
| Cooling System Fluid Capacity | 4.5gal | 17L |
| Engine Oil Fluid Capacity | 2.2gal | 8L |
| Max Speed | 11.7mph | 18.8km/h |
| Hydraulic System Fluid Capacity | 5.9gal | 22L |
| Chain Box Fluid Capacity - Each Side | 2gal | 7.6L |
| Tire Size | 12.00 x 16.5 | |
| Operating Voltage | 12V | |
| Alternator Supplied Amperage | 95amps |
03 Loader Specification
| Operating Load Rating | 2300lb | 1043kg |
|---|---|---|
| Bucket Capacity | 0.7yd3 | 0.5m3 |
04 Hydraulic Specification
| Pump Type | Gear | |
|---|---|---|
| Pump Flow Capacity | 21gal/min | 79.5L/min |
| Relief Valve Pressure | 3050psi | 21029kPa |
05 Dimensions Dimensions
| Length With Bucket | 11.29ft in | 3440mm |
|---|---|---|
| Width Over Tires | 5.09ft in | 1550mm |
| Ground Clearance | 9in | 228mm |
| Height To Top Of Cab | 6.67ft in | 2030mm |
| Wheelbase | 3.75ft in | 1140mm |
| Length W/O Bucket | 8.6ft in | 2620mm |
| Clearance At Max Lift And Dump | 7.55ft in | 2300mm |
| Reach At Max Lift And Dump | 29.9in | 760mm |
| Turning Radius From Center - Machine Rear | 78.75in | 2000mm |
| Turning Radius From Center - Inc Bucket | 80.2in | 2000mm |
?Questions & answersfrom this machine's data
- How much does a Case 435 skid steer weigh?
- A Case 435 skid steer has an operating weight of 6,830 lb (3,098 kg).
- How much can a Case 435 skid steer lift?
- A Case 435 skid steer has a rated operating capacity of 2,300 lb (1,043 kg).
- What engine does a Case 435 skid steer have?
- A Case 435 skid steer is powered by a Family III 334T/M2, Tier II certified engine producing 72 hp (54 kW).
- What is the ground clearance of a Case 435 skid steer?
- A Case 435 skid steer has a ground clearance of 9 in (228 mm).
- How long is a Case 435 skid steer?
- A Case 435 skid steer has an overall length of 11.3 ft (3,440 mm) with the bucket on the ground.
Data notes
Derived value. tipping load was not published directly in a usable form by the source. It was reconstructed from related published figures and accepted only after validating against the expected relationship between specifications for this machine class.
Method. Figures are manufacturer reference specifications, not measurements. Every value is checked for unit consistency, physically possible magnitude, and plausibility for its equipment class before publication; figures that fail any check are withheld rather than shown, and figures reconstructed from related data are marked above. Imperial and metric figures are reproduced as published, except where a note states otherwise.