Case 420CT
The Case 420CT is a compact track loader with an operating weight of 7,350 lb (3,334 kg), a 56 hp engine, a rated operating capacity of 2,500 lb (1,134 kg), and a tipping load of 5,000 lb (2,267.96 kg).
✓ QA-verified — every figure checked for unit consistency, physical possibility, and class plausibility; failures withheld →◆Where it sits in its classpercentile · compact track loaders
Among 184 compact track loaders , the Case 420CT sits below the median for its class:
- Operating weight 7,350 lb lighter than 81% (n=182)
- Engine power 56 hp less powerful than 87% (n=167)
- Rated operating capacity 2,500 lb lower-rated than 56% (n=156)
◇Scale drawingdrawn to scale · mm
01 Engine Specification
| Number Of Cylinders | 4 | |
|---|---|---|
| Engine Make | 2239 | |
| Engine Model | 422T/M2 | |
| Gross Power | 59hp | 44kw |
| Net Power | 56hp | 42kw |
| Power Measured @ | 2900rpm | |
| Peak Torque | 132lb ft | 179Nm |
| Torque Measured @ | 1700rpm | |
| Displacement | 134cu in | 2.2L |
| Aspiration | turbocharged |
02 Operational Specification
| Operating Weight | 7350lb | 3334kg |
|---|---|---|
| Cooling System Fluid Capacity | 4.5gal | 17L |
| Engine Oil Capacity | 2.8gal | 10.5L |
| Fuel Capacity | 22gal | 83.3L |
| Hydraulic System Fluid Capacity | 13.2gal | 50L |
| Alternator Supplied Amperage | 55amps | |
| Max Speed - High Range | 6.3mph | 10.1km/h |
03 Loader Specification
| Breakout Force | 4564lb | 2070kg |
|---|---|---|
| Operating Load | 2500lb | 1134kg |
| Bucket Capacity | 0.6yd3 | 0.5m3 |
04 Hydraulic Specification
| Pump Type | gear pump | |
|---|---|---|
| Pump Flow | 19.5gal/min | 73.8L/min |
| Relief Valve Pressure | 3000psi | 20684.3kPa |
05 Dimensions Dimensions
| Width Over Tracks | 5.42ft in | 1651mm |
|---|---|---|
| Height To Top Of Cab | 6.29ft in | 1920mm |
| Ground Clearance | 8in | 203mm |
| Clearance At Max Lift And Dump | 7.45ft in | 2270mm |
| Reach At Max Lift And Dump | 2.07ft in | 630mm |
| Turning Radius From Center - Machine Rear | 56.1in | 1420mm |
| Length With Bucket | 10.27ft in | 3130mm |
| Turning Radius From Center - Inc Bucket | 77.5in | 1970mm |
| Length With Out Bucket | 8.33ft in | 2540mm |
06 Undercarriage Dimensions
| Length Of Track On Ground | 4.71ft in | 1436mm |
|---|---|---|
| Track Gauge | 4.27ft in | 1300mm |
| Ground Contact Area | 1424in2 | 0.92m2 |
| Number Of Track Rollers Per Side | 3 | |
| Width Of Track | 12.6in | 320mm |
| Ground Pressure | 5.2psi | 35.8kPa |
Data notes
Derived value. tipping load was not published directly in a usable form by the source. It was reconstructed from related published figures and accepted only after validating against the expected relationship between specifications for this machine class.
Method. Figures are manufacturer reference specifications, not measurements. Every value is checked for unit consistency, physically possible magnitude, and plausibility for its equipment class before publication; figures that fail any check are withheld rather than shown, and figures reconstructed from related data are marked above. Imperial and metric figures are reproduced as published, except where a note states otherwise.