Case 420
The Case 420 is a skid steer loader with an operating weight of 5,813 lb (2,637 kg), a 56 hp engine, a rated operating capacity of 1,750 lb (794 kg), and a tipping load of 3,500 lb (1,587.58 kg).
✓ QA-verified — every figure checked for unit consistency, physical possibility, and class plausibility; failures withheld →◆Where it sits in its classpercentile · skid steer loaders
Among 360 skid steer loaders , the Case 420 sits below the median for its class:
- Operating weight 5,810 lb lighter than 72% (n=334)
- Engine power 56 hp less powerful than 66% (n=335)
- Rated operating capacity 1,750 lb lower-rated than 61% (n=288)
◇Scale drawingdrawn to scale · mm
01 Engine Specification
| Number Of Cylinders | 4 | |
|---|---|---|
| Engine Make | 2239 | |
| Engine Model | 422T/M2, Tier II certified | |
| Gross Power | 59hp | 44kw |
| Net Power | 56hp | 42kw |
| Power Measured @ | 2900rpm | |
| Aspiration | turbocharged | |
| Displacement | 134cu in | 2.2L |
02 Operational Specification
| Operational Weight | 5813lb | 2637kg |
|---|---|---|
| Fuel Capacity | 22gal | 83.3L |
| Cooling System Fluid Capacity | 4.5gal | 17L |
| Engine Oil Fluid Capacity | 2.8gal | 10.5L |
| Hydraulic System Fluid Capacity | 13.2gal | 50L |
| Max Speed | 6.5mph | 10.5km/h |
| Chain Box Fluid Capacity - Each Side | 2gal | 7.6L |
| Operating Speed | 6.9mph | 11km/h |
| Tire Size | 10.00 x 16.5 | |
| Operating Voltage | 12V | |
| Alternator Supplied Amperage | 55amps |
03 Loader Specification
| Operating Load Rating | 1750lb | 794kg |
|---|---|---|
| Bucket Capacity | 0.5yd3 | 0.4m3 |
04 Hydraulic Specification
| Pump Type | Gear | |
|---|---|---|
| Pump Flow Capacity | 19.5gal/min | 73.9L/min |
| Relief Valve Pressure | 3050psi | 21029kPa |
05 Dimensions Dimensions
| Length With Bucket | 10.27ft in | 3130mm |
|---|---|---|
| Width Over Tires | 4.11ft in | 1250mm |
| Height To Top Of Cab | 6.3ft in | 1920mm |
| Wheelbase | 3.45ft in | 1050mm |
| Length W/O Bucket | 8.34ft in | 2540mm |
| Clearance At Max Lift And Dump | 7.45ft in | 2270mm |
| Reach At Max Lift And Dump | 23.6in | 600mm |
| Turning Radius From Center - Machine Rear | 57.6in | 1460mm |
| Turning Radius From Center - Inc Bucket | 73.2in | 1860mm |
Data notes
Derived value. tipping load was not published directly in a usable form by the source. It was reconstructed from related published figures and accepted only after validating against the expected relationship between specifications for this machine class.
Method. Figures are manufacturer reference specifications, not measurements. Every value is checked for unit consistency, physically possible magnitude, and plausibility for its equipment class before publication; figures that fail any check are withheld rather than shown, and figures reconstructed from related data are marked above. Imperial and metric figures are reproduced as published, except where a note states otherwise.