Specification sheet Skid Steer Loader Ref case-410-skid-steer-loader

Case 410

The Case 410 is a skid steer loader with an operating weight of 5,483 lb (2,488 kg), a 49 hp engine, a rated operating capacity of 1,500 lb (681 kg), and a tipping load of 3,000 lb (1,360.78 kg).

✓ QA-verified — every figure checked for unit consistency, physical possibility, and class plausibility; failures withheld →
Operating weight
5,483lb
2,488kg
Engine power
49hp
37kW
Net Power
Rated operating capacity
1,500lb
681kg
Tipping load
3,000lb † — value reconstructed from related published figures
1,360.78kg
Bucket capacity
0.5yd³
0.4m³

◆Where it sits in its classpercentile · skid steer loaders

Among 360 skid steer loaders , the Case 410 sits below the median for its class:

  • Operating weight 5,480 lb lighter than 79% (n=334)
  • Engine power 49 hp less powerful than 75% (n=335)
  • Rated operating capacity 1,500 lb lower-rated than 77% (n=288)

◇Scale drawingdrawn to scale · mm

1920C203D3130A2540B
Side elevation
1920C1250E
Front elevation

01 Engine Specification

Number Of Cylinders 4
Engine Make 2239
Engine Model 422/M2, Tier II certified
Gross Power 51hp 38kw
Net Power 49hp 37kw
Power Measured @ 2900rpm
Aspiration Natural
Displacement 134cu in 2.2L

02 Operational Specification

Operational Weight 5483lb 2488kg
Fuel Capacity 22gal 83.3L
Cooling System Fluid Capacity 4.5gal 17L
Engine Oil Fluid Capacity 2.2gal 8.7L
Max Speed 6.8mph 11km/h
Hydraulic System Fluid Capacity 13.3gal 50.2L
Chain Box Fluid Capacity - Each Side 1.5gal 5.7L
Operating Speed 6.9mph 11km/h
Tire Size 10.00 x 16.5
Operating Voltage 12V
Alternator Supplied Amperage 41amps

03 Loader Specification

Breakout Force 4129lb --
Operating Load Rating 1500lb 681kg
Bucket Capacity 0.5yd3 0.4m3

04 Hydraulic Specification

Pump Type Gear
Pump Flow Capacity 18gal/min 68.3L/min
Relief Valve Pressure 3000psi 20684.3kPa

05 Dimensions Dimensions

Length With Bucket 10.26ft in 3130mm
Width Over Tires 4.08ft in 1250mm
Ground Clearance 8in 203mm
Height To Top Of Cab 6.28ft in 1920mm
Wheelbase 3.43ft in 1050mm
Length W/O Bucket 8.33ft in 2540mm
Clearance At Max Lift And Dump 7.48ft in 2270mm
Reach At Max Lift And Dump 23.6in 600mm
Turning Radius From Center - Machine Rear 57.6in 1460mm
Turning Radius From Center - Inc Bucket 73.2in 1860mm

?Questions & answersfrom this machine's data

How much does a Case 410 skid steer weigh?
A Case 410 skid steer has an operating weight of 5,483 lb (2,488 kg).
How much can a Case 410 skid steer lift?
A Case 410 skid steer has a rated operating capacity of 1,500 lb (681 kg).
What engine does a Case 410 skid steer have?
A Case 410 skid steer is powered by a 422/M2, Tier II certified engine producing 49 hp (37 kW).
What is the ground clearance of a Case 410 skid steer?
A Case 410 skid steer has a ground clearance of 8 in (203 mm).
How long is a Case 410 skid steer?
A Case 410 skid steer has an overall length of 10.3 ft (3,130 mm) with the bucket on the ground.

Data notes

†

Derived value. tipping load was not published directly in a usable form by the source. It was reconstructed from related published figures and accepted only after validating against the expected relationship between specifications for this machine class.

Method. Figures are manufacturer reference specifications, not measurements. Every value is checked for unit consistency, physically possible magnitude, and plausibility for its equipment class before publication; figures that fail any check are withheld rather than shown, and figures reconstructed from related data are marked above. Imperial and metric figures are reproduced as published, except where a note states otherwise.