Specification sheet Skid Steer Loader Ref case-40xt-skid-steer-loader

Case 40XT

The Case 40XT is a skid steer loader with an operating weight of 5,716 lb (2,592.74 kg), a 56 hp engine, a rated operating capacity of 1,500 lb (680.39 kg), and a tipping load of 3,000 lb (1,360.78 kg).

✓ QA-verified — every figure checked for unit consistency, physical possibility, and class plausibility; failures withheld →
Operating weight
5,716lb
2,592.74kg
Engine power
56hp
41.76kW
Net Power
Rated operating capacity
1,500lb
680.39kg
Tipping load
3,000lb † — value reconstructed from related published figures
1,360.78kg
Bucket capacity
0.6yd³
0.5m³

◆Where it sits in its classpercentile · skid steer loaders

Among 360 skid steer loaders , the Case 40XT sits below the median for its class:

  • Operating weight 5,720 lb lighter than 73% (n=334)
  • Engine power 56 hp less powerful than 66% (n=335)
  • Rated operating capacity 1,500 lb lower-rated than 77% (n=288)

◇Scale drawingdrawn to scale · mm

1920C203D3130A2540B
Side elevation
1920C1500E
Front elevation

01 Engine Specification

Number Of Cylinders 4
Engine Make 2239
Engine Model 4-390
Gross Power 60hp 44.8kw
Net Power 56hp 41.8kw
Power Measured @ 2000rpm
Aspiration Natural
Displacement 239cu in 4L

02 Operational Specification

Operational Weight 5716lb 2592.8kg
Fuel Capacity 22gal 83.3L
Cooling System Fluid Capacity 4.4gal 16.6L
Engine Oil Fluid Capacity 2.8gal 10.4L
Max Speed 6.8mph 11km/h
Hydraulic System Fluid Capacity 13.3gal 50.2L
Chain Box Fluid Capacity - Each Side 1.6gal 5.7L
Tire Size 10.00x16.5
Operating Voltage 12V
Alternator Supplied Amperage 65amps

03 Loader Specification

Breakout Force 3788lb 1718.3kg
Operating Load Rating 1500lb 680.4kg
Bucket Capacity 0.6yd3 0.5m3

04 Hydraulic Specification

Pump Type gear pump
Pump Flow Capacity 19.1gal/min 72.2L/min

05 Dimensions Dimensions

Length With Bucket 10.27ft in 3130mm
Width Over Tires 4.93ft in 1500mm
Ground Clearance 8in 203mm
Height To Top Of Cab 6.3ft in 1920mm
Wheelbase 3.45ft in 1050mm
Length W/O Bucket 8.34ft in 2540mm
Clearance At Max Lift And Dump 7.45ft in 2270mm
Reach At Max Lift And Dump 23.63in 600mm
Turning Radius From Center - Machine Rear 57.49in 1460mm
Turning Radius From Center - Inc Bucket 73.23in 1860mm

Data notes

†

Derived value. tipping load was not published directly in a usable form by the source. It was reconstructed from related published figures and accepted only after validating against the expected relationship between specifications for this machine class.

Method. Figures are manufacturer reference specifications, not measurements. Every value is checked for unit consistency, physically possible magnitude, and plausibility for its equipment class before publication; figures that fail any check are withheld rather than shown, and figures reconstructed from related data are marked above. Imperial and metric figures are reproduced as published, except where a note states otherwise.