Case 1840
The Case 1840 is a skid steer loader with an operating weight of 5,558 lb (2,521.07 kg), a 51 hp engine, a rated operating capacity of 1,400 lb (635.03 kg), and a tipping load of 2,800 lb (1,270.06 kg).
✓ QA-verified — every figure checked for unit consistency, physical possibility, and class plausibility; failures withheld →◆Where it sits in its classpercentile · skid steer loaders
Among 360 skid steer loaders , the Case 1840 sits below the median for its class:
- Operating weight 5,560 lb lighter than 76% (n=334)
- Engine power 51 hp less powerful than 70% (n=335)
- Rated operating capacity 1,400 lb lower-rated than 81% (n=288)
◇Scale drawingdrawn to scale · mm
01 Engine Specification
| Number Of Cylinders | 4 | |
|---|---|---|
| Engine Make | 2239 | |
| Engine Model | 4-390 | |
| Gross Power | 54hp | 40.3kw |
| Net Power | 51hp | 38.1kw |
| Power Measured @ | 2000rpm | |
| Max Torque | 179lb ft | 242.7Nm |
| Torque Measured @ | 1200rpm | |
| Displacement | 239cu in | 4L |
02 Operational Specification
| Operational Weight | 5558lb | 2521.1kg |
|---|---|---|
| Fuel Capacity | 19.5gal | 73.8L |
| Cooling System Fluid Capacity | 4.5gal | 17L |
| Engine Oil Fluid Capacity | 2.8gal | 10.4L |
| Hydraulic System Fluid Capacity | 10.6gal | 39.8L |
| Chain Box Fluid Capacity - Each Side | 1.3gal | 4.7L |
| Operating Speed | 6.3mph | 10km/h |
| Tire Size | 7.00 x 15 6PR | |
| Operating Voltage | 12V | |
| Alternator Supplied Amperage | 65amps |
03 Loader Specification
| Operating Load Rating | 1400lb | 635.1kg |
|---|---|---|
| Bucket Capacity | 0.3yd3 | 0.3m3 |
04 Hydraulic Specification
| Pump Type | gear | |
|---|---|---|
| Pump Flow Capacity | 15.3gal/min | 57.9L/min |
| Relief Valve Pressure | 2300psi | 15858kPa |
05 Dimensions Dimensions
| Length With Bucket | 10.44ft in | 3180mm |
|---|---|---|
| Width Over Tires | 4.79ft in | 1460mm |
| Ground Clearance | 6.7in | 170mm |
| Height To Top Of Cab | 6.44ft in | 1960mm |
| Wheelbase | 3.09ft in | 940mm |
| Length W/O Bucket | 8.04ft in | 2450mm |
| Clearance At Max Lift And Dump | 6.99ft in | 2130mm |
| Reach At Max Lift And Dump | 22.05in | 560mm |
| Turning Radius From Center - Machine Rear | 59.06in | 1500mm |
| Turning Radius From Center - Inc Bucket | 72.84in | 1850mm |
Data notes
Derived value. tipping load was not published directly in a usable form by the source. It was reconstructed from related published figures and accepted only after validating against the expected relationship between specifications for this machine class.
Method. Figures are manufacturer reference specifications, not measurements. Every value is checked for unit consistency, physically possible magnitude, and plausibility for its equipment class before publication; figures that fail any check are withheld rather than shown, and figures reconstructed from related data are marked above. Imperial and metric figures are reproduced as published, except where a note states otherwise.