Specification sheet Wheel Loader Ref case-1021f-wheel-loader
Case 1021F
The Case 1021F is a wheel loader with an operating weight of 53,791 lb (24,399.19 kg), a 262 hp engine, and a 5.5 yd³ (4.2 m³) bucket.
✓ QA-verified — every figure checked for unit consistency, physical possibility, and class plausibility; failures withheld → Operating weight
53,791lb
24,399.19kg
Engine power
262hp
195.4kW
Net Power Bucket capacity
5.5yd³
4.2m³
◆Where it sits in its classpercentile · medium wheel loaders
Among 198 medium wheel loaders (45,000–90,000 lb), the Case 1021F sits in the middle of its class:
- Operating weight 53,790 lb heavier than 52% (n=198)
- Engine power 262 hp less powerful than 69% (n=190)
- Bucket capacity 5.5 yd³ smaller-bucket than 56% (n=174)
◇Scale drawingdrawn to scale · mm
01 Hydraulic Cycle Times (Unloaded) Specification
| Total Cycle Time | 10.1sec |
|---|
02 Engine Specification
| Emissions Level | Interim Tier 4 | |
|---|---|---|
| Engine Speed - Rated Speed, Full Load | 2100rpm | |
| Number Of Cylinders | 6 | |
| Max. Torque Iso14396 | 1090.9lb ft | 1479Nm |
| Engine Model | FPT F2FE614C | |
| Net Power | 262hp | 195.4kw |
| Gross Power | 290hp | 216.3kw |
| Power Measured @ | 1800rpm | |
| Max Torque | 1091lb ft | 1479.2Nm |
| Displacement | 531cu in | 8.8L |
| Torque Measured @ | 1100rpm | |
| Aspiration | Turbocharged | |
| Torque Rise | 49% | |
| Alternator | 95amps |
03 Operational Specification
| Operating Weight | 53791lb | 24399.2kg |
|---|---|---|
| Fuel Capacity | 125gal | 473.2L |
| Hydraulic System Fluid Capacity | 66gal | 249.9L |
| Engine Oil Fluid Capacity | 8.1gal | 30.3L |
| Cooling System Fluid Capacity | 15gal | 56.8L |
| Transmission Fluid Capacity | 12gal | 45.4L |
| Front Axle/Diff Fluid Capacity | 13.5gal | 51.1L |
| Rear Axle/Diff Fluid Capacity | 13.5gal | 51.1L |
| Static Tipping Weight | 35001lb | 15876.2kg |
| Turning Radius | 20.9ft in | 6370mm |
| Tire Size | 26.5R25 |
04 Transmission Specification
| Differential Lock | F: Open / R: Open | |
|---|---|---|
| Transmission Type | Powershift | |
| Number Of Forward Gears | 4 | |
| Number Of Reverse Gears | 3 | |
| Max Speed - Forward | 23.6mph | 38km/h |
| Max Speed - Reverse | 16.1mph | 26km/h |
05 Hydraulic System Specification
| Steering Pump Type | Articulation | |
|---|---|---|
| Maximum System Pressure | 3650psi | 25165.9kPa |
| Pump Flow Capacity | 93gal/min | 352.1L/min |
| Raise Time | 6.2sec | |
| Dump Time | 1.3sec | |
| Lower Time | 2.6sec | |
| Pump Type | Axial Piston Pump |
06 Brakes Specification
| Service Brake | Wet Multi Disc |
|---|
07 Bucket Dimensions
| Dump Clearance At Max Raise | 10.34ft in | 3151mm |
|---|---|---|
| Breakout Force | 45096.68lb | 200.6kN |
| Bucket Capacity - Heaped | 5.5yd3 | 4.2m3 |
| Bucket Capacity - Struck | 4.07yd3 | 3.12m3 |
| Bucket Width | 10.49ft in | 3195mm |
08 Dimensions Dimensions
| Ground Clearance | 1.67ft in | 509mm |
|---|---|---|
| Length With Bucket On Ground | 29.18ft in | 8892mm |
| Width Over Tires | 9.81ft in | 2990mm |
| Height To Top Of Cab | 11.73ft in | 3573mm |
| Wheelbase | 11.65ft in | 3550mm |
| Hinge Pin - Max Height | 13.93ft in | 4243mm |
| Reach At Max Lift And Dump | 6.2ft in | 1887mm |
| Dump Reach @ Full Height, 45° Dump: Bucket | 4.16ft in | 1.27m |
Method. Figures are manufacturer reference specifications, not measurements. Every value is checked for unit consistency, physically possible magnitude, and plausibility for its equipment class before publication; figures that fail any check are withheld rather than shown, and figures reconstructed from related data are marked above. Imperial and metric figures are reproduced as published, except where a note states otherwise.