Specification sheet Wheel Loader Ref komatsu-wa1200-6-wheel-loader

Komatsu WA1200-6

The Komatsu WA1200-6 is a wheel loader with an operating weight of 477,080.4 lb (216,400 kg).

✓ QA-verified — every figure checked for unit consistency, physical possibility, and class plausibility; failures withheld →
Operating weight
477,080.4lb
216,400kg

Where it sits in its classpercentile · very large wheel loaders

Among 45 very large wheel loaders (>150,000 lb), the Komatsu WA1200-6 sits at the heavy end of its class:

  • Operating weight 477,080 lb heavier than 87% (n=45)

Not positioned on engine power — withheld or unpublished for this machine.

Scale drawingdrawn to scale · mm

5275A4585C
Front elevation

01 Steering System Specification

Steering System Type Articulated
Minimum Turning Radius At The Centre Of Outside Tire 30.2ft in 9200mm

02 Engine Specification

Horsepower, Gross-Sae J1995 1892.2hp 1411kw
Horsepower, Net-Iso 9249 1764.8hp 1316kw
Horsepower, Net-Sae J1349 1764.8hp 1316kw
Fan Drive Method Mechanical
Lubrication Method Gear pump, force-lubricatio
Filter Full-flow type bypass combined
Number Of Cylinders 16
Piston Displacement 3661.5cu in 60L
Engine Make 2238
Engine Model SSDA16V160E-2
Engine Type Water-cooled, 4-cycle
Air Cleaner Dry type
Governor All-speed, electronic
Displacement 3661.5cu in 60L
Aspiration Turbocharged, after cooledEGR
Bore 6.3in 159mm
Stroke 7.5in 190mm
Fuel System Modular common rail system

03 Driveline Specification

Maximum Speeds/Fwd Mph (Km/H) 11.6
Maximum Speeds/Rev Mph (Km/H) 12
Transmission Full-power shift, planetary gear
Service Brake Type Hydraulically actuated, wet disc brakes actuate on four wheels
Parking Brake Type Wet, multiple-disc
Number Of Speeds - Forward 3
Number Of Speeds - Reverse 3

04 Capacities Specification

Brake Oil 19.9gal 75L
Brake Cooling 76.7gal 290L
Fuel Tank - Diesel 1347.3gal 5100L
Cooling System 132.1gal 500L
Final Drive 177gal 670L
Hydraulic System 343.5gal 1300L
Engine Oil 74gal 280L
Torque Converter, Transmission And Retarder Cooling 92.5gal 350L

05 Operational Specification

Bucket Capacity Range – Sae 18.0 - 35.0 m3
Standard Bucket Capacity – Sae 26.2yd3 20m3
Static Tipping Load,Full Turn 236026.9lb 107060kg
Breakout Force 130000
Dump Clearance, @45 Degrees Dump Angle 20.7ft in 6305mm
Dump Reach, @45 Degrees Dump Angle 9.5ft in 2890mm
Bucket Width 15.8ft in 4810mm
Bucket Link Type Z-bar
Static Tipping Load, Full Straight 268809.7lb 121930kg

06 Transmission Specification

Transmission Type Full-power shift, planetary type
Number Of Forward Gears 4
Number Of Reverse Gears 4
Max Speed - Forward 17.4mph 28km/h
Max Speed - Reverse 17.6mph 28.3km/h

07 Tires Specification

Standard Fitment Size 60/80 R57

08 Weights Specification

Operating Weight 477080.4lb 216400kg

09 Hydraulic System Specification

Steering Pump Type Piston Pump
Loader Control Type Piston Pump
Number Of Cylinders 2
No.Of.Bucket Cylinders 2
Steering Pump 167.3gal/min 633L/min
Switch Pump 167.3gal/min 633L/min
Control Valve spool type
Control Positions Boom Raise, hold, lower, and float
Control Positions Bucket Tilt-back, hold, and dump
Hydraulic Cylinders Type Double-acting, piston type
Lift Cylinder 2
Bucket Cylinde Bore 11.9in 300mm
Bucket Cylinde Stroke 38.8in 985mm
Relief Valve Setting 31.4MPa 320 kg/cm2 4550
Raise Time 14.8sec
Dump Time 3.2sec
Lower Time 5.3sec

10 Axles Specification

Drive System Four-wheel drive
Front Fixed, semi-floating
Rear Center-pin support, semi-floating, 24 ̊ total oscillation

11 Hydraulic System Specification

Pump Type Piston Pump

12 Final Drive Specification

Reduction Gear Spiral bevel gear
Differential Gear Torque proportioning
Final Reduction Gear Planetary gear, single reduction

13 Brakes Specification

Parking Brake Dry Disc brake
Service Brake Hydraulically actuated
Emergency Brake Parking brake is commonly used

14 Dimensions Dimensions

Ground Clearance 1.81ft in 550mm
Width Over Tires 15.05ft in 4585mm
Height To Top Of Cab 17.31ft in 5275mm
Wheelbase 17.89ft in 5450mm
Length 561.82in 14270mm
Turning Circle 30.19ft in 9200mm

Method. Figures are manufacturer reference specifications, not measurements. Every value is checked for unit consistency, physically possible magnitude, and plausibility for its equipment class before publication; figures that fail any check are withheld rather than shown, and figures reconstructed from related data are marked above. Imperial and metric figures are reproduced as published, except where a note states otherwise.