Specification sheet Wheel Loader Ref clark-michigan-475c-wheel-loader
Clark Michigan 475C
The Clark Michigan 475C is a wheel loader with an operating weight of 167,762.98 lb (76,096 kg), a 630.3 hp engine, and a 12.01 yd³ (9.18 m³) bucket.
✓ QA-verified — every figure checked for unit consistency, physical possibility, and class plausibility; failures withheld → Operating weight
167,762.98lb
76,096kg
Engine power
630.3hp
470kW
Net Power Bucket capacity
12.01yd³
9.18m³
◆Where it sits in its classpercentile · very large wheel loaders
Among 45 very large wheel loaders (>150,000 lb), the Clark Michigan 475C sits at the compact end of its class:
- Operating weight 167,760 lb lighter than 93% (n=45)
- Engine power 630 hp less powerful than 80% (n=41)
◇Scale drawingdrawn to scale · mm
01 Engine Specification
| Number Of Cylinders | 12 | |
|---|---|---|
| Engine Make | 2347 | |
| Engine Model | VTA-1710C | |
| Net Power | 630.3hp | 470kw |
| Gross Power | 700.1hp | 522kw |
| Power Measured @ | 2000rpm | |
| Max Torque | 2173.6lb ft | 2947Nm |
| Displacement | 1708.7cu in | 28L |
| Torque Measured @ | 1500rpm |
02 Operational Specification
| Operating Weight | 167763lb | 76096kg |
|---|---|---|
| Fuel Capacity | 273gal | 1033.4L |
| Hydraulic System Fluid Capacity | 150gal | 567.8L |
| Engine Oil Fluid Capacity | 27gal | 102.2L |
| Cooling System Fluid Capacity | 60gal | 227.1L |
| Transmission Fluid Capacity | 33gal | 124.9L |
| Front Axle/Diff Fluid Capacity | 29.1gal | 109.8L |
| Rear Axle/Diff Fluid Capacity | 29.1gal | 109.8L |
| Static Tipping Weight | 101550lb | 46062.4kg |
| Turning Radius | 34.3ft in | 10439.5mm |
| Operating Voltage | 24V | |
| Alternator Supplied Amperage | 100amps | |
| Rear Axle Oscillation | 20degrees | |
| Tire Size | 41.25/70-39 34PR |
03 Transmission Specification
| Transmission Type | Clark countershaft powershift | |
|---|---|---|
| Number Of Forward Gears | 4 | |
| Number Of Reverse Gears | 4 | |
| Max Speed - Forward | 18.6mph | 29.9km/h |
| Max Speed - Reverse | 18.6mph | 29.9km/h |
04 Hydraulic System Specification
| Relief Valve Setting | 2700psi | 18615.9kPa |
|---|---|---|
| Pump Flow Capacity | 230.9gal/min | 874L/min |
| Raise Time | 12sec | |
| Dump Time | 3.7sec | |
| Lower Time | 6.3sec | |
| Pump Type | three gear type |
05 Bucket Dimensions
| Dump Clearance At Max Raise | 15.42ft in | 4699mm |
|---|---|---|
| Bucket Capacity - Heaped | 12.01yd3 | 9.18m3 |
| Bucket Capacity - Struck | 9.84yd3 | 7.52m3 |
| Bucket Width | 14.69ft in | 4475mm |
| Breakout Force | 95633.72lb | 425.4kN |
06 Dimensions Dimensions
| Ground Clearance | 1.92ft in | 584mm |
|---|---|---|
| Length With Bucket On Ground | 40.84ft in | 12446mm |
| Width Over Tires | 13.51ft in | 4115mm |
| Height To Top Of Cab | 16.01ft in | 4877mm |
| Wheelbase | 15.17ft in | 4623mm |
| Hinge Pin - Max Height | 20.59ft in | 6274mm |
| Reach At Max Lift And Dump | 5.92ft in | 1803mm |
Method. Figures are manufacturer reference specifications, not measurements. Every value is checked for unit consistency, physically possible magnitude, and plausibility for its equipment class before publication; figures that fail any check are withheld rather than shown, and figures reconstructed from related data are marked above. Imperial and metric figures are reproduced as published, except where a note states otherwise.