Specification sheet Wheel Loader Ref caterpillar-992k-wheel-loader
Caterpillar 992K
The Caterpillar 992K is a wheel loader with an operating weight of 214,948 lb (97,498.78 kg), a 801 hp engine, and a 16 yd³ (12.24 m³) bucket.
✓ QA-verified — every figure checked for unit consistency, physical possibility, and class plausibility; failures withheld → Operating weight
214,948lb
97,498.78kg
Engine power
801hp
597.4kW
Net Power Bucket capacity
16yd³
12.24m³
◆Where it sits in its classpercentile · very large wheel loaders
Among 45 very large wheel loaders (>150,000 lb), the Caterpillar 992K sits in the middle of its class:
- Operating weight 214,950 lb lighter than 56% (n=45)
- Engine power 801 hp less powerful than 51% (n=41)
◇Scale drawingdrawn to scale · mm
01 Engine Specification
| Number Of Cylinders | 12 | |
|---|---|---|
| Engine Make | 2236 | |
| Engine Model | C32 ACERT | |
| Net Power | 801hp | 597.4kw |
| Gross Power | 904hp | 674.2kw |
| Power Measured @ | 1750rpm | |
| Displacement | 8.5cu in | 0.2L |
| Bore | 5.7in | 144.8mm |
| Stroke | 6.4in | 162.6mm |
| Emissions | U.S. EPA Tier 4 Final | |
| Gross Power - Sae J1995 | 904hp | 674.2kw |
| Engine Model | Cat C32 with ACERT Technology | |
| Gross Power*** | 900hp | 671.2kw |
| Net Power*** | 814hp | 607kw |
| Emissions (U.S. Epa Tier 4 Final): Gross Power - Sae J1995 | 900hp | 671.2kw |
| Emissions (Tier 2 Equivalent): Net Power - Sae J1349 | 814hp | 607kw |
| Emissions (U.S. Epa Tier 4 Final): Net Power - Sae J1995 | 814hp | 607kw |
| Emissions (U.S. Epa Tier 4 Final): Peak Torque At 1,200 Rpm - Sae J1995 | 4765rpm | |
| Emissions (Tier 2 Equivalent): Gross Power - Sae J1995 | 907hp | 676.4kw |
| Emissions (Tier 2 Equivalent): Gross Power - Iso 14396 | 884hp | 659.2kw |
| Emissions (Tier 2 Equivalent): Rated Speed | 1750rpm | |
| Emissions (Tier 2 Equivalent): Net Power - Sae J1995 | 814hp | 607kw |
| Emissions (Tier 2 Equivalent): Peak Torque At 1,200 Rpm - Sae J1995 | 4796rpm | |
| Note (Tier 4 Final) (1) | These ratings apply at 1,750 rpm when tested under the specified standard conditions. | |
| Note (Tier 4 Final) (2) | Rating for net power advertised is based on power available when the engine is equipped with alternator, air cleaner, muffler, and on-demand hydraulic fan drive at maximum fan speed. | |
| Note (Tier 2 Equivalent) (1) | These ratings apply at 1,750 rpm when tested under the specified standard conditions. | |
| Note (Tier 2 Equivalent) (2) | Rating for net power advertised is based on power available when the engine is equipped with alternator, air cleaner, muffler, and on-demand hydraulic fan drive at maximum fan speed. | |
| Emissions (U.S. Epa Tier 4 Final): Net Power - Sae J1349 | 814hp | 607kw |
| Emissions (U.S. Epa Tier 4 Final): Gross Power - Iso 14396 | 884hp | 659.2kw |
| Emissions (U.S. Epa Tier 4 Final): Rated Speed | 1750rpm |
02 Operational Specification
| Operating Weight | 214948lb | 97498.8kg |
|---|---|---|
| Fuel Capacity | 413gal | 1563.4L |
| Engine Oil Fluid Capacity | 32gal | 120L |
| Cooling System Fluid Capacity | 77gal | 291.5L |
| Front Axle/Diff Fluid Capacity | 95gal | 359.7L |
| Rear Axle/Diff Fluid Capacity | 91gal | 344.5L |
| Static Tipping Weight | 113449.9lb | 51460kg |
| Operating Voltage | 24V | |
| Alternator Supplied Amperage | 150amps | |
| Tire Size | 45/65 45 |
03 Transmission Specification
| Transmission Type | Cat Planetary Power Shift | |
|---|---|---|
| Transmission Type | Planetary, powershift | |
| Number Of Forward Gears | 3 | |
| Number Of Reverse Gears | 3 | |
| Max Speed - Forward | 12.8mph | 20.6km/h |
| Max Speed - Reverse | 13.9mph | 22.4km/h |
| Forward - 1 | 4.3mph | 7km/h |
| Forward - 2 | 7.4mph | 12km/h |
| Forward - 3 | 12.6mph | 20.3km/h |
| Reverse - 1 | 4.7mph | 7.6km/h |
| Reverse - 2 | 8.1mph | 13.1km/h |
| Direct Drive - Forward 3 | 14.2mph | 22.9km/h |
| Direct Drive - Reverse 3 | 15.4mph | 24.8km/h |
| Direct Drive - Forward 2 | 8mph | 12.9km/h |
| Direct Drive - Reverse 2 | 8.8mph | 14.2km/h |
| Converter Drive - Forward 3 | 12.8mph | 20.6km/h |
| Converter Drive - Reverse 3 | 13.9mph | 22.4km/h |
| Direct Drive - Forward 1 | Lock-up Disabled | |
| Converter Drive - Forward 1 | 4.4mph | 7.1km/h |
| Converter Drive - Forward 2 | 7.6mph | 12.3km/h |
| Direct Drive - Reverse 1 | 4.9mph | 7.9km/h |
| Converter Drive - Reverse 1 | 4.6mph | 7.5km/h |
| Converter Drive - Reverse 2 | 8.1mph | 13.1km/h |
| Reverse - 3 | 13.8mph | 22.3km/h |
04 Tires Specification
| Tires | Choose from a variety of tires to match your application. |
|---|
05 Weights Specification
| Operating Weight - Standard Lift* | 220089lb | 99830.7kg |
|---|---|---|
| Operating Weight - High Lift** | 221847lb | 100628.2kg |
| Operating Weight - Standard Lift | 214948lb | 97498.8kg |
| Operating Weight - High Lift | 226249lb | 102624.9kg |
06 Buckets Specification
| Bucket Capacities | 10.7-12.3 m3 (14-16 yd3) |
|---|
07 Hydraulic System Specification
| Relief Valve Setting | 4500psi | 31026.4kPa |
|---|
08 Axles Specification
| Front | Fixed | |
|---|---|---|
| Rear | Oscillating | |
| Oscillation Angle | 10 degrees , 8 degrees with Stops |
09 Brakes Specification
| Brakes | Meets SAE J1473, OCT90 and ISO 3450:1992 |
|---|
10 Operating Specifications Specification
| Bucket Capacity Range | 10.7-12.3 m3 (14-16 yd3) | |
|---|---|---|
| Breakout Force | 128895lb | 58465.8kg |
| Rated Payload - High Lift | 42000lb | 19050.9kg |
| Rated Payload - Standard Lift | 48000lb | 21772.5kg |
| Operating Weight - Standard Lift* | 220089lb | 99830.7kg |
| Operating Weight - High Lift** | 221847lb | 100628.2kg |
| Operating Weight - Standard | 220089lb | 99830.7kg |
| Operating Weight - High Lift | 226249lb | 102624.9kg |
| Rated Payload - Standard (Face Material) | 52910.9lb | 24000kg |
| Rated Payload - High Lift (Face Material) | 46297.1lb | 21000kg |
| Operating Weight - Standard Lift | 214948lb | 97498.8kg |
11 Service Refill Capacities Specification
| Cooling System | 77gal | 291.5L |
|---|---|---|
| Fuel Tank | 413gal | 1563.4L |
| Crankcase | 32gal | 121.2L |
| Fuel Tank - Standard | 413gal | 1563.4L |
| Engine Crankcase | 32gal | 121.2L |
| Transmission | 45gal | 170.4L |
| Differential - Final Drives - Front | 95gal | 359.7L |
| Differential - Final Drives - Rear | 91gal | 344.5L |
| Cooling Systems | 77gal | 291.5L |
| Hydraulic Tank - Implement | 86gal | 325.6L |
| Hydraulic Tank - Steering/Brake | 42gal | 159L |
| Windshield Washer Fluid | 4.9gal | 18.6L |
| Hydraulic System - Implement | 86gal | 325.6L |
| Hydraulic System - Steering | 42gal | 159L |
| Ac Refrigerant | 6lb | 2.8kg |
| Ac Oil | 0.1gal | 0.3L |
12 Hydraulic Cycle Times Specification
| Raise | 9.4 s | |
|---|---|---|
| Dump | 1.8 s | |
| Lower Float Down | 3.7 s | |
| Rack Back | 4.4 s | |
| Total Hydraulic Cycle Time | 14.9 s | |
| Lower Float Down - Empty | 3.7 s | |
| Raise* | 9.4 s | |
| Dump* | 1.8 s |
13 Hydraulic System - Lift/Tilt Specification
| Lift/Tilt System - Circuit | Positive Flow Control | |
|---|---|---|
| Lift/Tilt System - Pump | Variable Displacement Piston | |
| Relief Valve Setting - Lift/Tilt | 4500 psi | |
| Tilt Cylinder - Stroke | 80.9in | 2054.9mm |
| Lift Cylinder - Bore | 11in | 279.4mm |
| Lift Cylinder - Stroke | 45.2in | 1148.1mm |
| Tilt Cylinder - Bore | 10.5in | 266.7mm |
| Maximum Flow At 1,850 Rpm | 254 gal/min |
14 Hydraulic System - Steering Specification
| Steering System - Circuit | Pilot, Load Sensing | |
|---|---|---|
| Steering System - Pump | Piston, Variable Displacement | |
| Steering Cut Off Pressure | 4500 psi | |
| Steering Cycle Times - Low Idle | 6.4 s | |
| Steering Cycle Times - High Idle | 4.4 s | |
| Maximum Flow At 1,350 Rpm | 95 gal/min |
15 Cab Specification
| Cab - Rops/Fops | Meets SAE and ISO standards. | |
|---|---|---|
| Rops/Fops | Meets SAE and ISO standards |
16 Loader Hydraulic System Specification
| Relief Valve Setting | 4500 psi | |
|---|---|---|
| Relief Valve Setting - Low Idle | 4500 psi | |
| Lift Cylinder, Double Acting - Bore | 11in | 279.4mm |
| Tilt Cylinder, Double Acting - Bore | 10.5in | 266.7mm |
| Lift Cylinder, Double Acting - Stroke | 45.2in | 1148.1mm |
| Tilt Cylinder, Double Acting - Stroke | 80.9in | 2054.9mm |
17 Model Specification
| Serial Number Prefix | 880 |
|---|
18 Operating Specifications - High Lift* Specification
| Breakout Force | 127813lb | 57975.1kg |
|---|---|---|
| Static Tipping Load - At 35 Degrees Articulation | 114760lb | 52054.3kg |
19 Operating Specifications - Standard Lift* Specification
| Breakout Force | 123439lb | 55991kg |
|---|---|---|
| Static Tipping Load - At 35 Degrees Articulation | 122010lb | 55342.9kg |
20 Sound Performance Specification
| Performance | Performance | |
|---|---|---|
| Operator Sound Pressure Level | The operator sound pressure level is 70 dB(A), measured according to the test procedures and conditions specified in ISO 6396:2008 for the standard machine configuration. The measurement was conducted at 70 percent of the maximum engine cooling fan speed. | |
| Hearing Protection | Hearing protection may be needed when the machine is operated with a cab that is not properly maintained or when the doors or windows are open for extended periods or in a noisy environment. | |
| Machine Sound Power Level - Standard Machine Configuration | The machine sound power level is 116 dB(A), measured according to the test procedures and conditions specified in ISO 6395:2008 for the standard machine configuration. The measurement was conducted at 70 percent of the maximum engine cooling fan speed. | |
| Machine Sound Power Level - Sound Suppressed Machine Configuration | The machine sound power level is 113 dB(A), measured according to the test procedures and conditions specified in ISO 6395:2008 for the sound suppressed machine configuration. The measurement was conducted at 70 percent of the maximum engine cooling fan speed. |
21 Dimensions - High Lift - Approximate Specification
| Ground To Top Of Rops | 18.7ft in | 5.7m |
|---|---|---|
| Ground To Top Of Exhaust Stacks | 17.3ft in | 5.3m |
| Ground To Top Of Hood | 13.3ft in | 4.1m |
| Ground To Bumper Clearance | 3.9ft in | 1.2m |
| Rear Axle - Centerline To Bumper | 13.8ft in | 4.2m |
| Wheel Base | 19.4ft in | 5.9m |
| Maximum Overall Length | 52.9ft in | 16.1m |
| Ground To Lower Hitch Clearance | 2.3ft in | 0.7m |
| Ground To Center Of Axles | 4.5ft in | 1.4m |
| Rack Back Angle - Ground Level | 42.8 degrees | |
| Rack Back Angle - Carry | 52.5 degrees | |
| B-Pin Height - Maximum Lift | 24.6ft in | 7.5m |
| Maximum Overall Height - Bucket Raised | 33.1ft in | 10.1m |
| Dump Angle At Maximum Lift | 50 degrees | |
| Reach - Maximum Lift | 6.9ft in | 2.1m |
| Tread Width | 10.9ft in | 3.4m |
| Clearance At 45 Degrees Dump (Tooth Tip) | 15.1ft in | 4.6m |
| Rack Back Angle - Maximum Lift | 65 degrees |
22 Dimensions - Standard Lift - Approximate Specification
| Ground To Top Of Rops | 18.7ft in | 5.7m |
|---|---|---|
| Ground To Top Of Exhaust Stacks | 17.3ft in | 5.3m |
| Ground To Top Of Hood | 13.3ft in | 4.1m |
| Ground To Bumper Clearance | 3.9ft in | 1.2m |
| Rear Axle - Centerline To Bumper | 13.8ft in | 4.2m |
| Wheel Base | 19.4ft in | 5.9m |
| Maximum Overall Length | 52ft in | 15.9m |
| Ground To Lower Hitch Clearance | 2.3ft in | 0.7m |
| Ground To Center Of Axles | 4.5ft in | 1.4m |
| Rack Back Angle - Ground Level | 43.4 degrees | |
| Rack Back Angle - Carry | 52.7 degrees | |
| B-Pin Height - Maximum Lift | 22.8ft in | 7m |
| Maximum Overall Height - Bucket Raised | 30.5ft in | 9.3m |
| Dump Angle At Maximum Lift | 50 degrees | |
| Reach - Maximum Lift | 7ft in | 2.2m |
| Tread Width | 10.9ft in | 3.4m |
| Clearance At 50 Degrees Dump (Tooth Tip) | 14.7ft in | 4.5m |
| Rack Back Angle - Maximum Lift | 65 degrees |
23 Operating Specifications - High Lift Specification
| Static Tipping Load - At 35 Degrees Articulation | 96853lb | 43931.8kg |
|---|---|---|
| Breakout Force | 129777lb | 58865.9kg |
24 Operating Specifications - Standard Lift Specification
| Static Tipping Load - At 35 Degrees Articulation | 113159lb | 51328.1kg |
|---|---|---|
| Standard Lift Breakout Force | 128895lb | 58465.8kg |
| High Lift Breakout Force | 127775lb | 57957.8kg |
| Breakout Force | 128895lb | 58465.8kg |
25 Bucket Dimensions
| Dump Clearance At Max Raise | 15.12ft in | 4607mm |
|---|---|---|
| Bucket Capacity - Heaped | 16yd3 | 12.24m3 |
| Bucket Capacity - Struck | 14yd3 | 10.71m3 |
| Breakout Force | 128895lb | 573.36kN |
| Bucket Width | 15.83ft in | 4824mm |
26 Dimensions Dimensions
| Ground Clearance | 2.25ft in | 682.76mm |
|---|---|---|
| Length With Bucket On Ground | 51.63ft in | 15736mm |
| Width Over Tires | 18.05ft in | 5499mm |
| Height To Top Of Cab | 18.63ft in | 5678.43mm |
| Wheelbase | 19.32ft in | 5888.74mm |
| Reach At Max Lift And Dump | 7.64ft in | 2326mm |
27 Dimensions* Dimensions
| Ground Clearance | 2.25ft in | 0.69m |
|---|---|---|
| Bumper Clearance | 3.86ft in | 1.18m |
| Height - Top Of Rops/Fops | 18.63ft in | 5.68m |
| Wheel Base Length | 19.32ft in | 5.89m |
| Height - Top Of Hood | 17.22ft in | 5.25m |
Method. Figures are manufacturer reference specifications, not measurements. Every value is checked for unit consistency, physically possible magnitude, and plausibility for its equipment class before publication; figures that fail any check are withheld rather than shown, and figures reconstructed from related data are marked above. Imperial and metric figures are reproduced as published, except where a note states otherwise.